background image

2

IEC-61010-1, EN 61010-1: Safety requirements for electrical equipment 

for measurement, control, and laboratory use, Part 1.

IP65 Enclosure rating (Face only), IEC 529

ELECTROMAGNETIC COMPATIBILITY

Notes

1. Backlit powered units require a power line filter to be installed, 

RLC LFIL0000 or equivalent, so as not to impair the function of the 
backlighting.

Refer to EMC Installation Guidelines for additional information.

11. 

CONSTRUCTION

: High impact plastic case with clear viewing window. 

The front panel meets NEMA 4X/IP65 requirements for indoor use when 
properly installed. Installation Category I, Pollution Degree 2. Panel gasket 
and mounting clip included.

12. 

WEIGHT

: 2 oz. (57 grams) [with battery]

TIMER RANGE SELECTION

The CUB7T’s timer range can be modified in the Program mode. The 

Program mode uses the PGM button (refer to photo) to switch between 
Program and Operate modes. The RESET button (refer to photo) is used to 
select the desired timer range. 

Note: Timer range and accumulated time on the display will be lost if the 

battery is removed from the unit

Connect wires between RST EN (Reset Enable) and COM. (Common); and 

between HS (Program Enable) and COM. (Common) to enable front push 
buttons. Press the PGM button to enter Program Mode, allowing selection of 
the desired timer range. The display will show 00000.000 (Timer Range 0.001 
sec). Repeatedly pressing the RST button will cycle through the available timer 
ranges as shown in the table. 
When the desired timer range is 
displayed, press PGM to load the 
range and return to operating 
mode. (

The CUB7T will remain 

in Program Mode until the PGM 
button is pressed.

) Remove the 

wire from the HS (Program 
Enable) terminal to prevent 
accidental changes to the timer 
range. Any new time accumulated 
will be at the new rate selected.

Note: To avoid incorrect display 

information, it is recommended 
that the CUB7T be reset after 
making programming changes.

Timer Range

00000.000

0.001 Sec

111111.11

0.01 Sec

2222222.2

0.1 Sec

33333333

1 Sec

4444444.4

0.1 Min

55555555

1 Min

666666.66

0.01 Hr

7777777.7

0.1 Hr

88888888

1 Hr

9999.99.99

Factory Use Only

PGM

RST

ANNUNCIATOR

INSTALLATION

The CUB7T meets NEMA 4X/IP65 requirements for indoor use when 

properly installed. The units are intended to be mounted into an enclosed 
panel. The viewing window and reset button are factory sealed for a 
washdown environment. A sponge rubber gasket and mounting clip are 
provided for installing the unit in the panel cut-out.

Installation Environment

The unit should be installed in a location that does not exceed the 

maximum operating temperature and provides good air circulation. Placing 
the unit near devices that generate excessive heat should be avoided.

The bezel should be cleaned only with a soft cloth and neutral soap 

product. Do NOT use solvents.

Continuous exposure to direct sunlight may accelerate the aging process of 

the bezel.

Do not use tools of any kind (screwdrivers, pens, pencils, etc.) to operate 

the push buttons of the unit.

The following procedure assures proper installation:

1. Cut panel opening to specified dimensions. Remove burrs and clean 

around panel opening.

2. Carefully remove and discard the center section of the gasket.
3. Slide the panel gasket over the rear of the counter body to the back of the 

bezel. Install CUB7T unit through the panel cut-out.

4. Insert the mounting screws onto both sides of mounting clip. Tip of screw 

should NOT project from hole in mounting clip.

5. Slide the mounting clip over the rear of the unit until the clip is against the 

back of the panel. The mounting clip has latching features which engage 
into mating features on the CUB7T housing. 

6. Note: It is necessary to hold the unit in place when sliding mounting clip 

into position.

7. Alternately  tighten  each  screw  to  ensure  uniform  gasket  pressure. 

Visually inspect the front panel gasket. The gasket should be compressed 
to about 75 to 80% of its original thickness. If not, gradually turn mounting 
screws to further compress gasket.

8. If the gasket is not adequately compressed and the mounting screws can no 

longer be turned, loosen mounting screws, and check that the mounting 
clip is latched as close as possible to the panel.

9. Repeat from step #5 for tightening mounting screws.

HS-6

+V-2

LS-4

3-RST EN

1-COM

5-RST

LATCHING 
FEATURE

BEZEL

GASKET

0.062"

(1.57 mm)

THICK

EXISTING

PANEL

0.05" to 0.20"

(1.3 to 5.1 mm)

THICK

MOUNTING

SCREW

MOUNTING 

CLIP

900 MHz 

± 

5 MHz

Immunity to EN 50082-2

200 Hz, 50% duty cycle

Electrostatic discharge

EN 61000-4-2

Level 2; 4 Kv contact 
Level 3; 8 Kv air

Electromagnetic RF fields

EN 61000-4-3

Level 3; 10 V/m 
80 MHz - 1 GHz

Fast transients (burst)

EN 61000-4-4

Level 4; 2 Kv I/O
Level 3; 2 Kv power 

1

RF conducted interference

EN 61000-4-6

Level 3; 10 V/rms 
150 KHz - 80 MHz

Simulation of cordless telephone

ENV 50204

Level 3; 10 V/m

Emissions to EN 50081-1

RF interference

EN 55022

Enclosure class B

DISPLAY DURING 

PROGRAMMING

TROUBLESHOOTING

For further technical assistance, contact technical support at the appropriate 
company numbers listed. 

Reviews: