Red-D-Arc D502K 5+4, Technical Manual

Page: 64 / 82

TM-4412 Page 60
D502K 5+4
Table 12-1. Lead List Summary For D502K 5+4 Eff w/LC110463 And Following
.
Table shows physical lead connections and should be used with circuit diagram (table replaces wiring diagram).
Apply small amount of dielectric grade, nonconductive electric grease (Miller Part No. 146 557) to connectors where factory-applied
grease had been present.
Lead Connections Lead Connections
––––B RC6 (2) – S3 (2)
––––H RC6 (1) – S3 (1)
0010A T1 SEC TO SR4 (AC)
0011A STATOR TO EXIT
0012A #1 COIL TO RANGE SWITCH
0013A #1 COIL TO RANGE SWITCH
0014A #1 COIL TO RANGE SWITCH
0015A #1 COIL TO RANGE SWITCH
0016A #1 COIL TO RANGE SWITCH
0017A #1 COIL TO RECTIFIER
0017A PC3 TO BUS BAR
0018A T1 SEC TO SR4 (AC)
0019A PC3 TO HEAT SINK (+)
0019B PC3 TO LEAD 19 FROM PC1 (E2)
0019C PC3 TO LEAD 19 FROM VOLTMETER (+)
0019D SR3 (+) TO WELD TERMINAL (+)
0019E SR4 (+) TO SR3 (+)
0019F SR5 (+) TO SR3 (+)
0019J PC1 (PLG8–E2) TO LEAD 19 FROM PC3
0021A STATOR TO EXIT
0022A #2 COIL TO RANGE SWITCH
0023A #2 COIL TO RANGE SWITCH
0024A #2 COIL TO RANGE SWITCH
0025A #2 COIL TO RANGE SWITCH
0026A #2 COIL TO RANGE SWITCH
0027A #2 COIL TO RECTIFIER
0027A PC3 TO BUS BAR
0030A PC3 TO HEAT SINK (–)
0030B PC3 TO LEAD 30 FROM PC1 (E1)
0030C PC3 TO LEAD 30 FROM VOLTMETER (–)
0030D SHUNT (OUTSIDE) TO LEAD 30 FROM
AMMETER
0030E SHUNT (INSIDE) TO LEAD 30 FROM AMMETER
0030F SR3 (–) TO WELD TERMINAL (–)
0030G SR4 (–) TO SR3 (–)
0030H SR5 (–) TO SR3 (–)
0030J PC1 (PLG8–E1) TO LEAD 30 FROM PC3
0031A STATOR TO EXIT
0032A #3 COIL TO RANGE SWITCH
0033A #3 COIL TO RANGE SWITCH
0034A #3 COIL TO RANGE SWITCH
0035A #3 COIL TO RANGE SWITCH
0036A #3 COIL TO RANGE SWITCH
0036A PC8 (PLG1–G1) TO PLG6 (3)
0036C RC6 (3) – S3 (3)
0037A #3 COIL TO RECTIFIER
0037A PC1 (PLG8–G2) TO LEAD 37 FROM SR3
0037A PC3 TO BUS BAR
0037B PC3 TO LEAD 37 FROM PLG3 (2)
0038A T1 SEC TO SR5 (AC)
0039A T1 SEC TO SR5 (AC)
0040A STARTER TO AMP METER (POS)
0041A AMP METER (NEG) TO CB10 (COPPER)
0042AB
BASE GROUND TO D10 (–)
0042AC CR5 (85) TO D10 (–)
0042AD FUEL SENDER TO BASE GROUND
0042AE GROUND CABLE TO OIL PRESSURE SWITCH
0042AF FUEL PUMP TO FUEL SENDER
0042BA SPLICE A TO SPLICE B
0042BB SPLICE TO D10 (NEG)
0042CC RC3 (2) TO LEAD 42JJ
0042DD SPLICE TO TIMER (NEG)
0042EE SPLICE TO HOUR MTER (NEG)
0042H PC1 (PLG8–F3) TO PC8 (PLG13–8)
0042JJ SPLICE TO LEAD 42 CC
0042K PC1 (PLG8–C1) TO PLG3 (2)
0042KK SPLICE TO LEAD 42 SS
0042L END BELL (BOTTOM–LEFT) – PC4 (GND)
0042L END BELL (BOTTOM–RIGHT) – PC5 (GND)
0042L END BELL (TOP–LEFT) – PC6(GND)
0042M ASSY TO TEMP GAUGE (5)
0042N GND STD (BASE) TO GND STUD (AUX PANEL)
0042P 1T (C–RIGHT) – GND STUD
0042R GFCI (GND) – GND STUD
0042S RC1 (GND) – GND STUD
0042SS SPLICE TO 42KK
0042T 076 (K) TO LEAD 42 FROM END BELL
0042U ASSY TO HOUR METER (–)
0042V ASSY TO FUEL GAUGE (5)
0043A START SWITCH (17) TO GLOW PLUGS
0043B START SWITCH JUMPER #17 TO #19
0043D S1 (19) TO D9 (–)
0043E GLOW PLUG TO FS1 (PULL)
0044A CR5 (87A) TO CB10 (SILVER)
0044B CB10 (SILVER) TO START SW (30)
0044C CB10 (SILVER) TO ALT (B)
0044H CR5 (87) TO TIMER (N.O.)
0044J CB10 (SILVER) TO CR1 (30)
0045A CR2 (30) TO FS1
0046A STOP SW (CENTER) TO CR 2 (87A)
0048A LEAD 48B TO S6 (9)
0054A CT2 TO CT1
0055A CT2 TO CT1
0060A D8 (POS) TO ALT (IND)
0061A D10 (+) TO CR1 (86)
0061B D8 (–) TO D9 (+)
0061C SPLICE TO HOUR METER (+)
0061CA D9 (+) TO D10 (+)
0061D SPLICE TO FUEL GAUGE (6)
0061E D8 (–) TO CR5 (86)
0061F TIMER (+) TO STOP SW (BOTTOM)
0061H SPLICE TO TEMP GAUGE (6)
0061J SPLICE TO TEMP GAUGE (2)
0061K FUEL PUMP TO CR1 (87A)