background image

Ref: PM-

DS-11-01-

Rev- C  

07.19

28 [1.1]

1675±2.5 [65.94 ±0.1]

910 [35.8]

382.5 [15.05]

956 [37.64]

997±2.5 [39.25 ±0.1]

17 [0.7]

45 [1.5] 

1000 [39]

1200 [47]

Scale: 1:1.57

11±0.2

[0.43 ±0.8]

6.6±0.2 [0.26 ±0.08]

20.5±0.5

[0.78 ±0.08]

30 [1.18]

22.5 [0.9] 

600 ±1 [23.6 ±0.04] 

GR

GR

GR

GR

CERTIFICATE BBA 0148

MCS

14

REC Installation Manual - N-Peak - IEC 61215 /61730
Rev C - 07.19 

Ref: NE-06-22

tECHNiCal ProPErtiEs: rEC N-PEak blaCk sEriEs

Fig. 14: Panel dimensions: REC N-Peak Black Series

Specifications subject to change without notice.

WARRANTy

IEC 61215, IEC 61730 & UL 1703;  

IEC 62804, IEC 61701, IEC 62716, IEC 62782 

ISO 9001: 2015, ISO 14001: 2004, OHSaS 18001: 2007

20 year product warranty
25 year linear power output warranty, maximum 
degression in performance of 0.5% p.a., giving 
86% at end of year 25. 

See warranty conditions for further details.

GENERAL DATA

Cell type: 

120 half-cut mono c-Si n-type cells 

6 strings of 20 cells in series

Glass: 

3.2 mm solar glass with  

anti-reflection surface treatment

Backsheet: 

Highly reflective and resistant 

polymeric construction (black)

Frame: 

anodized aluminum (black)

Junction box:  

3-part, 3 bypass diodes, IP67 rated 

in accordance with IEC 62790

Cable: 

4 mm² solar cable, 1.0 m + 1.2 m 

in accordance with EN 50618

Connectors: Stäubli 

MC4 PV-KBT4/KST4 (4 mm²) 

in accordance with IEC 62852 

IP68 only when connected

Origin: 

Made in Singapore

LOW LIGhT BEhAvIOUR

TEMPERATURE RATINGS 

*

MAXIMUM RATINGS

MEChANICAL DATA

Dimensions: 

1675 x 997 x 30 mm

area: 

1.67 m²

Weight: 

18 kg

Operational temperature: 

-40 ... +85°C

Maximum system voltage: 

1000 V

Design load (+): snow  

4666 Pa (475 kg/m²)

+

 

Maximum test load (+): 

7000 Pa (713 kg/m²)

*

Design load (-): wind  

1600 Pa (163 kg/m²)

+

 

Maximum test load (-): 

2400 Pa (245 kg/m²)

*

Max series fuse rating: 

25 a

Max reverse current: 

25 a

+

 Calculated using a safety factor of 1.5 

* See installation manual for mounting instructions

CERTIFICATIONS

Measurements in mm [in]

Nominal Module Operating Temperature: 

44°C

 (±2°C)

Temperature coefficient of P

MPP

-0.35 %/°C

Temperature coefficient of V

OC

-0.27 %/°C

Temperature coefficient of I

SC

0.04 %/°C

* The temperature coefficients stated are linear values

rel. Efficiency (%)

take-e-way WEEE-compliant recycling scheme

100

200

300

400

500

600

700

800

900

1000

85

90

95

100

105

irradiance (W/m²)

Typical low irradiance performance of module at STC:

ELECTRICAL DATA @ STC

Product code

*

: RECxxxNP

Nominal Power - P

MPP

 (Wp) 

305

310

315

320

325

Watt Class Sorting - (W)

0/+5

0/+5

0/+5

0/+5

0/+5

Nominal Power Voltage - V

MPP

 (V) 

33.3

33.6

33.9

34.2

34.4

Nominal Power Current - I

MPP

 (a) 

9.17

9.24

9.31

9.37

9.46

Open Circuit Voltage - V

OC

 (V) 

39.3

39.7

40.0

40.3

40.7

Short Circuit Current - I

SC

 (a) 

10.06

10.12

10.17

10.22

10.28

Panel Efficiency (%) 

18.3

18.6

18.9

19.2

19.5

Values at standard test conditions (STC: air mass aM 1.5, irradiance 1000 W/m², temperature 25°C), based on a production spread with a 

tolerance of V

OC 

& I

SC

 ±3% within one watt class. * Where xxx indicates the nominal power class (P

MPP

) at STC above.

ELECTRICAL DATA @ NMOT

Product code

*

: RECxxxNP

Nominal Power - P

MPP

 (Wp) 

214

217

221

224

228

Nominal Power Voltage - V

MPP

 (V) 

31.1

31.4

31.7

32.0

32.2

Nominal Power Current - I

MPP

 (a) 

6.86

6.91

6.97

7.01

7.08

Open Circuit Voltage - V

OC

 (V) 

36.7

37.1

37.4

37.7

38.0

Short Circuit Current - I

SC

 (a) 

7.53

7.57

7.61

7.65

7.69

Nominal module operating temperature (NMOT: air mass aM 1.5, irradiance 800 W/m², temperature 20°C, windspeed 1 m/s). 

* Where xxx indicates the nominal power class (P

MPP

) at STC above.

Summary of Contents for ALPHA BLACK Series




















Reviews: