background image

Rear View Safety 

Reverse With Confidence

 ™

4

5

PLEASE READ THE ENTIRE MANUAL AND FOLLOW THE INSTRUCTIONS AND 
WARNINGS CAREFULLY. FAILURE TO DO SO CAN CAUSE SERIOUS DAMAGE 
AND/OR INJURY, INCLUDING LOSS OF LIFE. BE SURE TO OBEY ALL APPLI-
CABLE LOCAL TRAFFIC AND MOTOR VEHICLE REGULATIONS AS IT PERTAINS 

TO THIS PRODUCT.  IMPROPER INSTALLATION WILL VOID 

MANUFACTURER’S WARRANTY.

SAFET

Y   

INF

ORMA

TION

Before drilling please check that no cable or wiring is on the other side 
of the wall. Please clamp all wires securely to reduce the possibility 
of them being damaged while vehicle is in use. Keep all cables away 

from hot or moving parts and electrical noisy components.

We recommend doing a benchmark test before installation

to insure that all components are working properly.

BEF

ORE  Y

OU  B
EGIN

IN NO EVENT SHALL SELLER OR MANUFACTURER BE

LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF

ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM

ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.

If you have questions about this product, contact:

Rear View Safety

1797 Atlantic Avenue

Brooklyn, NY 11233

Tel: 1.800.764.1028

Summary of Contents for RVS-123












Reviews: