background image

 

2

FCC Certifications

 

This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules.    These limits are designed to provide 

reasonable protection against harmful interference in a residential installation.    This 

equipment generates, uses and can radiate radio frequency energy and, if not installed and 

used in accordance with the instructions, may cause harmful interference to radio 

communications.    However, there is no guarantee that interference will not occur in a 

particular installation.    If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user 

is encouraged to try to correct the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

CAUTION

Any changes or modifications not expressly approved by the grantee of this device could 

void the user’s authority to operate the equipment.   

This device complies with Part 15 of the FCC rules.    Operation is subject to the following 

two conditions:    (1) This device may not cause harmful interference, and (2) This device 

must accept any interference received, including interference that may cause undesired 

operation. 

 

FCC RF Radiation Exposure Statement 

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with a minimum distance of 

20cm between the radiator and your body.   

 

CE Mark Warning

 

This is a Class B product. In a domestic environment, this product may cause radio 

interference, in which case the user may be required to take adequate measures. 

All trademarks and brand names are the property of their respective proprietors. 

Specifications are subject to change without prior notification. 

Summary of Contents for WP102













Reviews: