background image

2

WARRANTY INFORMATION

The benefits provided to you under the following warranty are in addition to any other rights and remedies available to

you under the law.

1. Warranty

If:
(a)

during the first 12 months from the date of purchase (Burner Warranty Period) there is a defect in the Real Flame

gas burner; or

(b) during the first 12 months from the date of purchase (Parts Warranty Period) there is a defect in the gas valves or

other parts of the Real Flame Pit Fire, due to improper workmanship or material, Real Flame will replace or repair

the Real Flame Gas Burner without charge. Any replacement product is warranted only for the time remaining on

the original Burner Warranty Period or the Parts Warranty Period as relevant.

2. Registration

You must register to receive the benefit of this warranty by completing the warranty registration on our website

(www.realflame.com.au) or completing and mailing the attached registration card within 30 days of purchase of

your Real Flame Gas Burner (or, if the Real Flame Gas Burner is fitted to a new home, within 30 days of the date

of settlement of purchase of such new home).

3. Exclusions

Real Flame is not obliged to replace or repair the Real Flame Gas Burner under clause 1 if: 

(a)

it has been improperly stored, installed, connected, used, operated or repaired, or damaged, abused, tampered

with, altered (without our written approval), or not maintained in strict accordance with our installation and

operating instructions; or

4. Limit of Liability

The warranty provided under this warranty is limited to replacement or repair of the Real Flame Gas Burner only,

at our option. To the extent permitted by law, Real Flame excludes liability for consequential loss or any other loss

or damage caused to property or persons arising from any cause whatsoever, and damage arising from normal

wear and tear.

5. Claiming under the Warranty

In order to claim under this warranty you must, within the Burner Warranty Period or the Parts Warranty Period (as

relevant), contact Real Flame, providing the original proof of purchase and the details below:

Supplier Name___________________________________________________________________________
Date Of Purchase / settlement of property if new home _________________
Model / Serial Number_______________________
This warranty does not cover the cost of claiming under the warranty or transporting the Real Flame Gas Burner to and

from the supplier.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a

replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure

does not amount to a major failure.

If you would like to speak to someone about your Real Flame Gas Burner or claiming under this warranty, please

contact the Real Flame Service Warranty Desk on 03 8706 2000.

Real Flame Pty Ltd ACN 006 311 155
Head Office: 1340 Ferntree Gully Road, Scoresby 3179
Telephone: 03 8706 2000  Facsimile: 03 8706 2001

Summary of Contents for PIT FIRE SERIES
























Reviews: