Reaim BY02-VBW Instruction Manual Download Page 3

3

 

EN

 

 

 

damaged  extension  cords.  Examine 
extension  cord  before  using    and 
replace  if  damaged.  Do  not  abuse 
extension  cord  and  do  not  yank  on  any 
cord  to  disconnect.  Keep  cord    away 
from  heat  and  sharp  edges.  Always 
disconnect  the  extension  cord  from  the 
receptacle  before  disconnecting  the 
product from the extension cord. 
WARNING 

–  To  reduce  the  risk  of 

electrocution,  keep  all  connections  dry 
and  off  the  ground.  Do  not  touch  plug 
with wet hands. 

 

GENERAL SAFETY REGULATIONS

 

 

WARNING: 

Keep  operating  area  clear 

off all persons 

 

WARNING: 

Before  each  use  pressure 

must be released! Trigger on wand  then 
start the washer 

 

WARNING: 

Do  not  overreach  or  stand 

on unstable support. Keep good footing 
and balance at all times. 

 

WARNING: 

Follow  the  maintenance 

instructions specified in the manual. 

 

WARNING: 

To  reduce  the  risk  of 

electrocution,  don’t  start  and  run  the 
machine  in  the  rain  or  storm.  Keep  all 
connections dry and off the ground.  Do 
not  touch  plug  with  wet  hands.  It  is 
strictly  prohibited  to  let  water  leak  into 
the machine. 

 

WARNING: 

When  the  machine    is 

turned  on,  the  interior  pumps  start  and 
continue  to  run  even  if  the  pressure 
wand  trigger  has  not  been  depressed. 
Running  the  machine  for  more  than  3 
minutes 

without 

depressing 

the 

pressure wand trigger could cause  heat 

damage  to  the  motor  and  pumps. 
Please  do  not  leave  the  machine 
running  unattended  or  unused for  more 
than 3 minutes. 

 

WARNING: 

When  the  machine  is 

running,  please  maintain  a  constant 
water  supply.  Without  water  circulation 
will  damage  the  sealing  rings  of  the 
machine. 

 

WARNING: 

It  is  necessary  to    turn  on 

the  spray  lance  within  one  or  two 
minutes  after  the  machine  has  been 
started.  Otherwise,  the  temperature  of 
the circulating water within the machine 
will  soon  rise  to  a  critical  point,    which 
will  cause  damage  to  the  sealing  rings 
inside the machine. 

 

WARNING: 

Don’t  start  and  run  the 

machine  in  a  place  excessively  cold  so 
as  to  prevent  the  machine  from  the 
freezing current. 

 

WARNING: 

This  appliance  has  been 

designed  for  only  using  cleaning  water, 
do not use corrosive chemicals. 

 

WARNING: 

Do  not  use  the  appliance 

within the range of persons unless  they 
wear protective clothing. 

WARNING: 

Do not direct the jet  against 

yourself  or  others  in  order  to  clean 
clothes or footwear. 

 

WARNING: 

Disconnect 

from 

the 

electrical  power  supply  before  carrying 
out user maintenance. 

WARNING: 

To  ensure  the  appliance 

safety  to  please use  only  original  spare 
parts  from  the  manufacturer    or 
approved  by  the  manufacturer.  Do  not 
use  the  machine  before  you  change 
them       if       they       are     damaged. 

Summary of Contents for BY02-VBW













Reviews: