manualshive.com logo in svg

Reach Technology PoE4N/10G, Manual

Share
Download
Reach Technology PoE4N/10G Manual Download Page 15

Reach PoE4N/10G Tester Manual 1.1 

06/15/2020 

Page 15 

6. 

Ethernet Cables 

 

The performance of a CAT6A rated link is dependent on the cabling, connectors, mated 

connections and hardware components that make up the link. 

 

The PoE4N/10G data path passes 10GBASE-T traffic from each test port to the adjacent test 

port (ports 1-2, 3-4, etc.). The data path connections are made through magnetics and signal 

relays for compatibility with Phy-based cable diagnostics. When passing 10GBASE-T traffic 

through the PoE4N/10G data path, it is important to consider the type of cable, plugs and 

jacks used as part of that link. 

 

The PoE4N/10G data paths are all tested to the TIA CAT6A permanent link test limit using 

the DSX-5000 and the DSX-PLA004 permanent link adapters as shown in Figure 1 below. 

The permanent link consists of two 40meter CAT6A cables. Each 40 meter length of cable 

consists of a plug mated to the test port and a jack mated to the DSX-PLA004 permanent link 

adapter. The combination of cable and connectors shown in Figure 1 was found to have the 

best performance. 

 

 

Figure 1: Po#4/10G Permanent Link Test Setup 

Summary of Contents for PoE4N/10G




























Reviews:

No comments

Brands by name

Popular brands

Load more brands