RDS P232U Quick Installation Manual Download Page 11 | Manualshive

Page: 11 / 15

RDS P232U Quick Installation Manual Download Page 11

11

4.2

Communication Setup

For setting of some additional communication parameters, first open the Device Setup card. If previous steps have been done right, you’ll see
the following window:

The Communication setup represents the encoder’s port setup, Address List setup and UECP setup at one place.
A description of each item follows:

Options

Port 1 Speed

Here you may change the RS-232 port speed if it is required by the application.
Default speed of port 1 is 2400 bps.

UECP Configuration

General UECP Enable

Enable the UECP if your broadcast automation system or RDS data provider uses this protocol.
Leave disabled otherwise.

Address List

Up to two encoder address numbers in range 0 to 63, separated by comma.

Site List

Up to two site address numbers in range 0 to 1023, separated by comma.

PSN Settings

Note: The PSN (Program Service Number) settings have effect for UECP control only. Selectable PSN for each program set allow easier
integration of the RDS encoder into existing networks.

The PSN for main program can be set in RDS Content – System – Miscellaneous.
The PSN for EON service can be set in RDS Content – Networking – EON.

Default Configuration for each Program set:

PSN Main

1

EON 1 PSN

2

EON 2 PSN

3

EON 3 PSN

4

EON 4 PSN

5

DSN (fixed)

Equal to the Program

set number (1 to 6)

Store the settings to the
encoder

Read current settings
from the encoder

«
...
9
10
11
12
13
...
»

Summary of Contents for P232U
















Reviews:

No comments