manualshive.com logo in svg

RDS P232U, Quick Installation Manual, Page: 10 / 15

Share
Download
RDS P232U Quick Installation Manual Download Page 10

10 

 

 
 

4

 

Software Installation 

 

4.1

 

Establishing a First Communication with the RDS Encoder 

 

To configure the RDS encoder before first use, you may use either the USB (Port 2) or RS-232 (Port 1). 

 

1.

 

Install the Windows control software called ‘Magic RDS 4’, run the setup 
exe file and go through the simple installation wizard. 

2.

 

In the case of USB connection install the USB driver now. 

TIP: Latest operating systems already come with the USB driver 
included.

 

3.

 

Make sure the RDS encoder is connected and powered, all connectors 
are seated completely.  

4.

 

Run the Magic RDS software using Windows Start button. 

5.

 

Double-click on the ‘Add new connection’ icon. 

6.

 

Select your device model (P232U). Choose the Serial/USB connection 
and select the COM port the RDS encoder is connected to. 

Note: You may find/change the assigned COM port number in Windows 
Control Panels - System 

–

 (Hardware) - Device Manager.

 

7.

 

Finally click on the Add button. You should see "Connected" or 
"Opened" in the Recent Events box. Now you are ready. The settings 
are saved automatically. 

8.

 

Configure the basic RDS settings. 
Especially check the pages 

RDS Content – Program

 and 

Device 

Setup – Analog Control

. 

9.

 

To change the setting, click on the Test button first. Then, to make that 
setting permanent, click on the Apply button. 

10.

 

The Recent Events box and status bar at the bottom of the window 
show whether the data was sent successfully. If an error is shown, 
check the connection to the RDS encoder, its power supply and 
whether a correct COM port is selected in the connection setup. 

11.

 

Follow the Magic RDS help for further details, tools and configuration 
options. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Note: The RDS encoder contains two types of memory. These are marked as RAM and EEPROM. Like any other computing system the RAM 
holds all operational data which are also used for transmission whilst the EEPROM is used for the data storage during power-off. By default the 
button Test will fill the RAM only. The Apply or Store button saves the data into EEPROM. 
If the user forgets to store the data into EEPROM, that settings will be lost when the power is disconnected. 

 

P232U 

Summary of Contents for P232U
















Reviews:

No comments