RCF TT1-A Owner'S Manual Download Page 7

7

ENGLISH

REAR

PANEL

 

FEMALE XLR INPUTS (BAL/UNBAL). The system accept XLR input connectors.

 

MALE  XLR  SIGNAL  OUTPUT.  The  output  XLR  connector  provides  a  loop  through  for 

speakers daisy chaining. The balanced connector is connected in parallel and can be used to 
send the audio signal to other amplified speakers, recorders or supplementary amplifiers.

 

SYSTEM SET UP ENCODER. Push the encoder to select a function (gain reduction, delay, 

preset). Rotate the encoder to select a value or a preset.

 

GAIN REDUCTION LED. Pushing the encoder once the gain reduction indicator lights green. 

Then rotate the encoder to reduce the gain to the right level.

 

DELAY LED. Pushing the encoder twice the delay indicator lights green. Then rotate the 

encoder to delay the speaker. The delay is expressed in meters.

 

PRESET LED. Pushing the encoder three times the preset indicator lights green. Then rotate 

the encoder to load the right preset to the speaker.

 

SYSTEM  SET  UP  DISPLAY.  Display  the  system  setting  values.  In  case  of  RDNet  active 

connection a rotating segment will light up.

 

RDNET LOCAL SETUP/BYPASS. When released the local setup is loaded and RDNet can 

only monitor the speaker. When switched the RDNet setup is loaded and bypass any speaker 
local preset.

 

RDNET RECALL LED. This orange LED lights up when the LOCAL SETUP/BYPASS switch is 

pressed. If connected, RDNet is taking control of the speaker the speaker.

 

AC RDNET IN/OUT PLUG OPTION. The AC RDNET IN/OUT PLUG optional accessory can 

be installed removing a blind panel on the right side of the board. In the picture the installed 
accessory is shown.

 

LIMITER LED. The amplifier has a built in limiter circuit to prevent clipping of the amplifiers 

or overdriving the transducers. When the soft clipping circuit is active the LED blinks RED. It is 
okay if the limit LED blinks occasionally. If the LED lights continuously, turn down the signal 
level.

1

2

3

4

5

6

7

8

9

10

11

1

2

11

10

9

8

7

12

13

14

3

6

4

5

Summary of Contents for TT1-A





















Reviews: