RCF TT1-A Owner'S Manual Download Page 4

4

ENGLISH

1.

 

All the precautions, in particular the safety ones, must be read with special attention, as 

they provide important information.

2. 

Power supply from mains

The mains voltage is sufficiently high to involve a risk of electrocution; install and 

a. 

connect this product before plugging it in.
Before powering up, make sure that all the connections have been made correctly and 

b. 

the voltage of your mains corresponds to the voltage shown on the rating plate on the 
unit, if not, please contact your RCF dealer.
The metallic parts of the unit are earthed through the power cable. An apparatus with 

c. 

CLASS I construction shall be connected to a mains socket outlet with a protective 
earthing connection.
Protect the power cable from damage; make sure it is positioned in a way that it 

d. 

cannot be stepped on or crushed by objects.
To prevent the risk of electric shock, never open this product: there are no parts inside 

e. 

that the user needs to access.

3.

 Make sure that no objects or liquids can get into this product, as this may cause a short 

circuit.
This apparatus shall not be exposed to dripping or splashing. No objects filled with liquid, 
such as vases, shall be placed on this apparatus. No naked sources (such as lighted candles) 
should be placed on this apparatus.

4. 

Never attempt to carry out any operations, modifications or repairs that are not expressly 

described in this manual.
Contact your authorized service centre or qualified personnel should any of the following 
occur:

the product does not function (or functions in an anomalous way).

 -

The power cable has been damaged.

 -

Objects or liquids have got in the unit.

 -

The product has been subject to a heavy impact.

 -

5.

 If this product is not used for a long period, disconnect the power cable.

6.

 If this product begins emitting any strange odours or smoke, switch it off immediately 

and disconnect the power cable.

7.

 Do not connect this product to any equipment or accessories not foreseen.

For suspended installation, only use the dedicated anchoring points and do not try to hang 
this product by using elements that are unsuitable or not specific for this purpose. Also 
check the suitability of the support surface to which the product is anchored (wall, ceiling, 
structure, etc.), and the components used for attachment (screw anchors, screws, brackets 
not supplied by RCF etc.), which must guarantee the security of the system / installation 
over time, also considering, for example, the mechanical vibrations normally generated by 
transducers.
To prevent the risk of falling equipment, do not stack multiple units of this product unless 
this possibility is specified in the user manual.

8. RCF S.p.A. strongly recommends this product is only installed by professional 
qualified installers (or specialised firms) who can ensure correct installation 
and certify it according to the regulations in force.
The entire audio system must comply with the current standards and regulations 
regarding electrical systems.

9.

 Supports and trolleys. 

The  equipment  should  be  only  used  on  trolleys  or  supports,  where  necessary,  that  are 
recommended by the manufacturer. The equipment / support / trolley assembly must be 

SAFETY

PRECAUTIONS

IMPORTANT

Summary of Contents for TT1-A





















Reviews: