RCA RTS7131B User Manual Download Page 4

4

EN

CONNECTIONS

CONNECT AUDIO THROUGH AN ANALOG AUDIO CABLE

1.  Connect an Audio Cable (not included) from the AUX IN jacks to the AUDIO OUT jacks of your TV, Set-Top 

Box or Blu-ray/DVD Player.

2.  Connect a 3.5mm Audio Cable (not included) from the LINE IN jack to the AUDIO OUT jacks or from the AUX 

IN jacks to the Headphone Out jack of your TV, Set-Top Box or Blu-ray/DVD Player.

CONNECT AUDIO THROUGH A DIGITAL OpTICAL CABLE

3.  Connect an Optical Cable (not included) from the OPTICAL IN jack to the OPTICAL OUT jack of your TV, Set-

Top Box or Blu-ray/DVD Player.

Note: OPTICAL IN only supports PCM signal. You may need to activate PCM (Downmix) on your source device, 

e.g. TV, Set-Top Box or Blu-ray/DVD Player.

Plug one end of a 3.5mm Audio Cable (not included) 

into the LINE IN jack and other end into your iPad®, 

iPhone®, iPod® or other audio devices.

pLACEMENT

The Soundbar can be placed freestanding on a table or mounted on a wall. 

pLACING THE SOUNDBAR ON A WALL

The Soundbar requires additional mounting hardware 

that must be purchased separately.

1.  Install the Wall Mount Brackets to the Soundbar as 

shown.

2.  Place the Wall Mount Template (included) on the 

wall  and  then  mark  the  locations  of  the  screw 

holes.

3.  Drill  the  screws  (not  supplied)  into  the  wall 

carefully.

4.  Gently hang the Soundbar onto the  screws in the 

wall.

Note: Allow 2mm space between screw and the wall 

for fitting the wall mount bracket.

CAUTION:

•  We recommend that Wall-mounting be carried out 

by  a  professional.  The  wall  mount  bracket  “key-

holes” are intended for use with #8 (Imperial) or 

M4  (Metric)  with  head  size:  Diameter  7.5  -  9.4 

mm. Additional or alternative parts may be needed 

for certain types of wall constructions.

•  Make  sure  that  the  wall-mount  is  fixed  securely 

enough so that it meets safety standards.

•  Allow at least 2” (5 cm) separation in all directions 

between the Sound Bar and other AV equipment 

(such as your TV or Set-Top Box).

•  It  is  recommended  that  all  cables  (AC  adapter 

and Audio cables) be connected to the Sound Bar 

before placing it on the wall.

Wall Mount
Bracket

Summary of Contents for RTS7131B






Reviews: