RCA MRM400 Instruction Manual Download Page 43 | Manualshive

Page: 43 / 58

background image

Copyright © 2015 RCA Communications Systems

43

MRM400

TM

VHF Marine Two-Way Radio Instruction Manual

set in advance.

4. Push [DSC] to enter the standby condition
for Position Report Call.

- Channel 70 is selected and “READY” appears.

5. Push [DSC] to transmit the Position Report
Call.

6. After the Position Report Call has been
transmitted, stand by on Channel 70 until an
acknowledgement is received.

- “WAIT ACK” scrolls at the Channel Comment
Indicator.

7. Push any key to exit the function and return
to the normal operation.

■

Receiving a Position Request Call

While monitoring Channel 70 and a Position
Request Call is received:

1. “DSC” appears and “RCV POS REQUEST”
scrolls at the Channel Comment Indicator.

2. Push any key to stop the beep.

Scrolls

«
...
41
42
43
44
45
...
»

Summary of Contents for MRM400



























































Reviews:

No comments

Related manuals for MRM400

HD Radio NS-HDRAD

Brand: Insignia Pages: 17

Brand: Denver Electronics Pages: 14

Brand: SOUNDMASTER Pages: 72

Voyager MAX KA900

Brand: Kaito Pages: 29

Brand: Hyundai Pages: 24

Brand: AML Oceanographic Pages: 18

Brand: Japan Radio Co. Pages: 36

Brand: Albrecht Pages: 16

Brand: Microgate Pages: 11

Brand: Ocean Digital Pages: 26

Brand: Chinavision Pages: 14

Brand: JVCKENWOOD Pages: 18

Brand: Vertex Standard Pages: 44

Brand: Vertex Standard Pages: 80

Brand: Arion Pages: 31

Brand: COMNET ERICSSON Pages: 32

Brand: Naxa Pages: 11

Brand: Siemens Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands