background image

Page 4 of 15 

SPECIFICATIONS 

 

Length:

 

24.5” at deck (622mm) 

Width:  

11” (330mm) 

Weight:

 

40 oz (Ready to run except cells) (2.2 kg) ABS hull with Cordite motor.  The 
ABS and fiberglass hulls weigh virtually the same and are equally strong.  The 
ABS is much easier to build and finish, but fiberglass has “snob appeal.” 
 

 

Sport Recommendations: 

 

Motor:

 

Graupner 700BB (included in GR1157 Hardware Package) 

Propeller:

 

Stock Graupner plastic propeller 

Batteries: 

(2) six-cell “stick” packs available from your local hobby shop, with a variety 
of brand names.  We recommend a minimum of 1500mAH packs for adequate 
runtime.  For longer runtime, we recommend you visit Hill’s RC 
(http://sjshill.hypermart.net) and tell them we sent you. 

Speed Control:

  Any 12-cell capable speed control capable of 60 Amps continuous (our SC-2 

AsTec ESC, or Hughey mechanical, as well as others. 

Hardware:

 

GR1157 Hardware Package 

 

 

Club Racing Recommendations: 

 

Motor:

 

Graupner 700BB, Graupner 770 (Cobalt), or Astro 25 (Cobalt) 

Propeller:

 

Octura X438-X450 (depends on motor) (requires adapter with GR1157) 

Batteries: 

(2) six-cell “matched” packs available from your local hobby shop or various 
online sources including Hill’s RC (http://sjshill.hypermart.net). 

Speed Control:

  Any 12-cell capable speed control capable of 60 Amps continuous (our SC-2 

AsTec ESC, or Hughey mechanical, as well as others. 

Hardware:

 

GR1157 Hardware Package or a Fullers, Octura, or BBY Racing 3/16” setup 

 

 

Pro Racing Recommendations: 

 

Motor:

 

FDM Cordite, 4-Turn, or Aveox 

Propeller:

 

X642-X448 (depends on setup) 

Batteries:

 

(2) six-cell “Pro” matched packs available from your local hobby shop or 
various online sources including Hill’s RC (http://sjshill.hypermart.net). 

Speed Control:

  Any 12-cell capable speed control capable of 60 Amps continuous (our SC3, 

AsTec ESC, or Hughey mechanical, as well as others. 

Hardware:

 

Fullers, Octura, BBY Racing, or your own custom setup. 

 
 
 
 
 
 

Summary of Contents for UL-10 Wiggins
















Reviews: