background image

Fi

d

b

b il

&

h

B il

M

l

Finned copper tube gas boilers & water heaters – Boiler Manual

21

F

F

 Never use an open fl 

ame to test for gas 

leaks. Always use an approved leak detection method. 

Failure to comply with this warning can cause extensive 

property damage, severe personal injury or death!

Whenever the gas supply piping is pressure tested the boiler/water 

heater gas controls must be protected. If the test pressure is equal 
to, or less than 

1/2 psig

3.5 kPa

 isolate the boiler/water heater 

by closing it’s manual shut off  valve, see Figure 14. If the test pressure 
is greater than, or equal to 

1/2 psig

3.5 kPa

, disconnect the boiler/

water heater and its individual shut-off  valve.

ELECTRICAL WIRING 

Electrical Power Connections

  Label all wires prior to disconnection when servicing 

controls. Wiring errors can cause improper and 
dangerous operation! Verify proper operation aft er 
servicing.

  Au moment de l’entretien des commandes, étiquetez 

tous les fi ls avant de les débrancher. Des erreurs de 
câblage peuvent entraîner un fonctionnement inadé-
quat et dangereux. S’assurer que l’appareil fonctionne 
adéquatement une fois l’entretirn terminé.

Th e electrical connections to this boiler/water heater must be made 

in accordance with all applicable local codes and the latest revision 
of the National Electrical Code, ANSI /NFPA-70. Installation should 
also conform with CSA C22.1 Canadian Electrical Code Part I if 
installed in Canada. 

Install a separate 120 volt 15 amp or 20 amp circuit breaker for the 

boiler/water heater and pump, see Table 11. A properly rated shut-
off  switch should be located at the boiler/water heater. Th e boiler/

water heater must be grounded in accordance with the authority 

having jurisdiction, or if none, the latest revision of the National 

Electrical Code, ANSI/NFPA-70.

Table 11 

Futera III Electrical Requirements

Recommended

Futera III

Circuit Breaker

*Running

Model

(Amps)

Amps

MB/MW 500

15

3.9

MB/MW 750 - 1000

15

6.0

MB/MW 1250 - 2000

20

11.4

*Use separate circuit breaker that is properly sized for pump and
pump contactor.

Line voltage fi eld wiring of any controls or other devices must 

conform to the temperature limitation of type TEW wire at 

95°F

35°C

 above room temperature. Use copper conductors with a 

minimum size of #14 awg. Use appropriate wiring materials for 
units installed oudoors. Th e wire size must be compatible with the 
total amp draw of the circuit.  

Refer to the wiring diagram supplied with the boiler/water heater 

for proper wiring connections and boiler full load amperage (FLA).

GENERAL OPERATION

Before proceeding read and fully understand the 

instructions contained in this manual. Do not att empt 
to operate this boiler/water heater if it has not been 
installed in accordance with the guidelines set forth 
in this manual. Failure to comply with this warning 
can result in extensive property damage, severe per-
sonal injury or death!

Should overheating occur or the gas supply fail to shut off , turn off  
the manual gas control valve to the appliance.  Do not interrupt 
water fl ow through the boiler/water heater.

En cas de surchauff e ou si l’alimentation en gaz ne s’arrête pas, fermez 

manuellement le robinet d’arrêt de l’admission de gaz.

Hydronic Heating Boilers 

Open the make-up water valve and slowly fi ll the boiler and all of 
the radiation with water. Ensure that all bleed and drain valves are 

closed.

Adjust the make-up water pressure regulator so a minimum

12 psig

82.7 kPa

 system pressure is maintained at the highest point in the 

system piping. If a make-up water pump is used adjust it to maintain 
a minimum 

12 psig

82.7 kPa

 system pressure.

Open the system bleed and drain valves, one at a time, to purge 
the air trapped in the heating system piping.

With the boiler off , run the system pump for at least 30 minutes 

and bleed the system piping using the bleed valves. If strainers are 
used in the system piping, the make- up water valve should be closed 
and the strainers checked and cleaned.

Th e system expansion tank should be checked to ensure that the 

correct water level in the tank is maintained. Th e tank should be 
less than half full of water with the system full and adjusted to the 
correct operating pressure.

Start the boiler as described in the “OPERA

 TING INSTRUCTIONS” 

section. Run the boiler for at least an hour.  Th e system pump(s) 
and all radiation units must be operated during this time. Ensure 
that the make-up water valve is open.

Shut the boiler off  and open the bleed valves to purge the air trapped 
in the heating system piping. Close the make-up water valve and 
check and clean the strainers and make-up water pressure reducing 

valve.

Open the make-up water valve and adjust the system pressure if 

necessary. Th e system should be checked and bled aft er three days 
of operation.

Summary of Contents for FUTERA III Series













































Reviews: