background image

SERIES 8800 & 8900 FINNED COPPER

GAS BOILERS (MODEL HB) &

WATER HEATERS (MODEL HW)

INSTALLATION & OPERATION MANUAL

CIOM-6

42-9134 Rev. 4

260 North Elm Street

7555 Tranmere Drive

Westfield, MA 01085

Mississauga, Ontario L5S 1L4 Canada

Phone: (413) 568-9571

Phone: (905) 670-5888

Fax: (413) 568-9613

Fax: (905) 670-5782

INSTALLER, THESE INSTRUCTIONS TO BE AFFIXED ADJACENT TO THE HEATER.

CONSUMER, RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE PURPOSES.

WARNING: If the information in this manual is not followed exactly, a fire
or explosion may result causing property damage, personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.

WHAT TO DO IF  YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot  reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or
the gas supplier.

DESIGNED AND TESTED ACCORDING TO A.S.M.E. BOILER AND PRESSURE
VESSEL CODE, SECTION IV FOR A MAXIMUM ALLOWABLE WORKING PRESSURE
OF 160 PSI, 

1103 kPa

 WATER.

WARNING: Failure to properly vent this unit can cause excessive amounts of carbon
monoxide resulting in severe personal injury or death!

Summary of Contents for 8800 Series

















































Reviews: