RBH Sound 180 Operator'S Manual Download

Page: 27 / 28

English –

TECHNICAL SPECIFICATIONS

Engine:

18 HP VANGUARD V-TWIN Briggs & Stratton *

Battery:

12 Volts/22 Ah

Front tyres:

16 X 6.50 - 8

Rear tyres:

20 X 10.00 - 8

Front tyres pressure:

100 kPa (1 Bar)

Rear tyres pressure:

70 kPa (0,7 Bar)

Transaxle:

HYDRO-GEAR MODEL NO: 310-0650

Forward speed

0 - 9 km/h

Reverse speed

0 - 4 km/h

Turning radius:

74 cm

Cutting heights:

6 heights: from 25 to 90 mm

Mowing size:

Twin-blade; 102 cm

Mower deck:

Suspended

Blade clutch:

Warner Electro-magnetic clutch

Discharge:

Rear, with grass collector as standard

Weight (18 HP):

Gross: 262 Kg

Net: 247 Kg

Tractor dimensions (L x W x H):

240 x 106 x 110 cm

IMPORTANT
* Refer to model and type numbers when purchasing replacement parts.

For improvement purposes, specifications and design are subject to change, without notice.
Please be advised that no legal claims, of whatsoever they might be, can be used upon the information contained in this
manual.

When performing repairs, make sure that only genuine parts are used. Use of non-original parts will void the warranty.

Summary of Contents for 180





























Search results

Summary of Contents for 180

Reviews:

Related manuals for 180

Brands by name

Popular brands

RBH Sound 180, Operator'S Manual

Search results

Summary of Contents for 180

Reviews:

Related manuals for 180

Brands by name

Popular brands