RBH Access Technologies Integra32 Hardware Manual Download Page 22 | Manualshive

Page: 22 / 64

background image

Chapter 2
Intelligent Field Panel

Integra32

™

Hardware Guide

RBH Access Technologies Inc.

18

Elevator Control

Integra32™ Elevator Control uses a modified URC2000 board with ELC firmware.

Up  to  four  ELC-08  relays  boards  may  be  connect  (strung)  together  for  a  maximum  of
thirty-two  dry  contact  outputs  per  Elevator  Control  panel.    These  contacts  are
programmed as “on state de-energized” so that the release of the fire signal or power will
place the outputs in the ON state.  There are red LEDs (one for each relay) that turn on
as each relay is energized therefore indicating an off state.

The green LED next to the data input connector flash when communications is lost.
Another green LED next to the Fire Signal connector indicates the presence of a Fire
Signal or Fire Signal Bypass.

«
...
20
21
22
23
24
...
»

Summary of Contents for Integra32

































































Reviews:

No comments

Related manuals for Integra32

Brand: VAT Pages: 29

Brand: Balboa Instruments Pages: 19

Brand: T-Verter Pages: 121

Brand: Happy Pages: 10

Brand: Eaton Pages: 288

Brand: Gardena Pages: 14

Brand: Gardena Pages: 8

Brand: Hama Pages: 7

Brand: Hama Pages: 44

Brand: RadioMaster Pages: 10

Brand: K&K Pages: 6

Brand: Lamtec Pages: 22

Brand: Paradox Pages: 2

FUTERA XLF Series

Brand: RBI Pages: 128

Brand: RBH Access Technologies Pages: 36

Brand: S&C Pages: 11

Brand: S&C Pages: 24

Brand: S&C Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands