RAYTAC VH2402 User Manual Download Page 12

 

12

6.6 Powering the Phone on and off, Standby and Sleep Mode: 

¾

 

Press and hold 

  for 3 seconds until the display turn on/off. 

¾

 

Standby mode: 

To extend battery life, the backlight turns off automatically when no 

activity is detected for 15 seconds (

 

shown on display ). The backlight turns back 

on when you press any key. 

¾

 

Sleep mode:

 If the computer loses connection to Internet or the phone is out of range 

with USB dongle (

  shown on display) for 1 minute, the phone will automatically 

enter Sleep mode and the display screen shuts off.   

To recovery from Sleep mode, follow the steps below: 

1.  Confirm the computer is connected to Internet. 

2.  Move back within the range from USB dongle. 

3.  Press any key to recovery from Sleep mode. 

4.  Check the connection icon 

 is displayed.  

 

6.7 Charging the Batteries: 

¾

 

Plug the small connector on the supplied USB charging cable into the USB connector 

port on the bottom of your phone. 

¾

 

With your computer turned on, plug the other end of the cable into a USB connector 

on the computer, the phone will begin recharging automatically. 

¾

 

The charging indicator appears on the display, you can make/receive calls while 

charging. 

¾

 

When the charging indicator stays in full charge    remove the charging cable. 

 

Note:

 The charging time depends on the battery discharging condition, load and the 

temperature, it takes approximately 5 hours to full charge the batteries. 

 

 

 

 

 
 

Summary of Contents for VH2402





















Reviews: