background image

 

43 

 

WARRANTY 

 

RAYPAK WATER HEATER WARRANTY – AUSTRALIA ONLY 

RAYPAK WATER HEATER MODELS  B0147 

 

1.

 

THE RHEEM WARRANTY – GENERAL 

1.1

 

This warranty is given by Rheem Australia Pty Limited ABN 21 098 823 511 of 1 Alan Street, Rydalmere New South Wales. 

1.2

 

Rheem offer a trained and qualified national service network who will repair or replace components at the address of the water heater subject 
to the terms of the Rheem warranty. Rheem Service, in addition can provide preventative maintenance and advice on the operation of your 
water heater. The Rheem Service contact number is available 7 days a week on 131031 with Service personnel available to take  your call 

from 8am to 8pm daily (hours subject to change). 

1.3

 

For details about this warranty, you can contact us on 131031 or by email at 

[email protected]

 (not for service bookings). 

1.4

 

The terms of this warranty are set out in section 2 and apply to water heaters manufactured after 1

st

 January 2012. 

1.5

 

If  a  subsequent  version  of  this  warranty  is  published,  the  terms  of  that  warranty  will  apply  to  water  heaters  manufactured  after  the  date 
specified in the subsequent version. 

 

2.

 

TERMS OF THE RHEEM WARRANTY AND EXCLUSIONS TO IT 

2.1

 

The decision of whether to repair or replace a faulty component is at Rheem’s sole discretion. 

2.2

 

If you require a call out and we find that the fault is not covered by the Rheem warranty, you are responsible for our standard call out charge. 
If you wish to have the relevant component repaired or replaced by Rheem, that service will be at your cost. 

2.3

 

Where a failed component is replaced under this warranty, the balance of the original warranty period will remain effective. The replacement 

does not carry a new Rheem warranty. 

2.4

 

Where the water heater is installed outside the boundaries of a metropolitan area as defined by Rheem or further than 25 km from either a 
regional Rheem branch office or an Accredited Rheem Service  Agent's office, the  cost  of transport,  insurance and travelling between the 
nearest branch office or Rheem Accredited Service Agent’s office and the installed site shall be the owner’s responsibility. 

2.5

 

Where  the  water  heater  is  installed  in  a  position  that  does  not  allow  safe  or  ready  access,  the  cost  of  that  access,  including  the  cost  of 
additional materials handling and/or safety equipment, shall be the owner’s responsibility. In other words, the cost of dismantling or removing 
cupboards, doors or walls and the cost of any special equipment to bring the water heater to floor or ground level or to a serviceable position 

is not covered by this warranty. 

2.6

 

This  warranty  only  applies  to  the  original  and  genuine  Rheem  water  heater  in  its  original  installed  location  and  any  genuine  Rheem 
replacement parts. 

2.7

 

The Rheem warranty does not cover faults that are a result of: 
a)

 

Accidental damage to the water heater or any component (for example: (i) Acts of God such as floods, storms, fires, lightning strikes and 
the like; and (ii) third party acts or omissions). 

b)

 

Misuse or abnormal use of the water heater. 

c)

 

Installation not in accordance with the Owner’s Guide and Installation Instructions or with relevant statutory and local requirements in the 

State or Territory in which the water heater is installed. 

d)

 

Connection at any time to a water supply that does not comply with the water supply guidelines as outlined in the Owner’s Guide and 
Installation Instructions. 

e)

 

Repairs, attempts to repair or modifications to the water heater by a person other than Rheem Service or a Rheem Accredited Service 
Agent. 

f)

 

Faulty plumbing or faulty power supply. 

g)

 

Failure to maintain the water heater in accordance with the Owner's Guide and Installation Instructions. 

h)

 

Transport damage. 

i)

 

Fair wear and tear from adverse conditions (for example, corrosion). 

j)

 

Cosmetic defects. 

2.8

 

Subject to any statutory provisions to the contrary, this warranty excludes any and all claims for damage to furniture, carpet, walls, foundations 

or any other consequential loss either directly or indirectly due to leakage from the water heater, or due to leakage from fittings and/ or pipe 
work of metal, plastic or other materials caused by water temperature, workmanship or other modes of failure. 

2.9

 

If the water heater is not sized to supply the hot water demand in accordance with the guidelines in the Rheem water heater literature, any 
resultant fault will not be covered by the Rheem warranty. 

 

 

Summary of Contents for B0147













































Reviews: