background image

28

Operation

Connect With Your Smartphone

The Wi-Fi Garage Door Opener is compatible with up to 16 myQ

®

enabled accessories. Up to 10 devices can be

paired to the Wi-Fi garage door opener’s internal gateway. These devices can be controlled with the myQ

®

App.

These devices include any combination of myQ

®

garage door openers, Wi-Fi garage door openers, myQ

®

light

controls, myQ

®

gate operators or myQ

®

commercial door operators. A myQ

®

Internet Gateway (828LG) can be

added if you need to control more than 10 devices using the myQ

®

App. Up to 6 devices can be paired to garage

door opener itself (controlled by garage door opener through 900MHz). These devices include any combination
of myQ

®

light controls or a garage door and gate monitor.

YOU WILL NEED:

Wi-Fi enabled smartphone, tablet or laptop

Broadband Internet Connection

Wi-Fi signal in the garage (2.4 GHz, 802.11b/g/n required), see page 1

Password for your home network (router's main account, not guest network)

myQ

®

serial number located on the garage door opener

DOWNLOAD THE myQ®APP TO SET UP AN ACCOUNT AND CONNECT

Open and close your door, get alerts and set schedules from anywhere. Connected smart garage door openers
also receive software updates to ensure the opener has the latest operational features.

1.

Download the myQ® App.

2.

Set up an account and connect.

An LED on the garage door 
opener will indicate Wi-Fi 
status. See table below.

Learn 
Button

Command 
LED

LED

Learn
Button

WiFi Status

LED

Definition

Blue

Off - Wi-Fi is not turned on.
Blinking - Garage door opener is in Wi-Fi learn mode.
Solid - Mobile device connected to the garage door opener.

Blue and Green

Blinking - Attempting to connect to router.

Green

Blinking - Attempting to connect to the Internet server.
Solid - Wi-Fi has been set up and garage door opener is connected to the
internet.

NOTES:
To erase the Wi-Fi settings, see page 32.

Summary of Contents for CORPORAL II STANDARD Series













































Reviews: