background image

28

The Remote Control Battery

Care of Your Opener

Limit and force adjustments:

Weather conditions may cause some 
minor changes in door operation 
requiring some re-adjustments, 
particularly during the first year of 
operation.

Pages 23 and 24 refer to the limit and 
force adjustments. Only a screwdriver is 
required. Follow the instructions carefully.

Repeat the safety reverse test 
(Adjustment Step 3, page 25) after any 
adjustment of limits or force.

Maintenance Schedule

Once a Month

Manually operate door. If it is unbalanced or binding, call a 

• 

trained door systems technician.

Check to be sure door opens & closes fully. Adjust limits and/

• 

or force if necessary. See pages 23 and 24.

Repeat the safety reverse test. Make any necessary 

• 

adjustments. See Adjustment Step 3.

Once a Year

Oil door rollers, bearings and hinges. The opener does not 

• 

require additional lubrication. Do not grease the door tracks.

FORCE CONTROLS

1

3

9

7

5

1

3

9

7

5

KG

KG

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this 
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the 
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards for HOME OR OFFICE USE. Operation is subject to the 
following two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired operation.

LIMIT CONTROLS

To prevent possible SERIOUS INJURY OR DEATH:

NEVER allow small children near batteries.

• 

If battery is swallowed, immediately notify doctor.

• 

To reduce risk of fire, explosion or chemical burn:

Replace ONLY with 3V2032 coin batteries.

• 

DO NOT 

• 

recharge, disassemble, heat above 212°F (100°C) or 

incinerate.

The lithium battery should produce 
power for up to 5 years.

To replace battery, use the visor clip 
or screwdriver blade to pry open the 
case as shown. Insert battery 
positive side up (+).

Dispose of old battery properly.

Replace the battery with only 
3V2032 coin cell batteries.

Battery 
positive 
side up (+)

Summary of Contents for Commander II Safety Signal 3240RGD





































Reviews: