background image

LIMITED WARRANTY

SPECIFICATIONS

The Raynor ControlHoist Optima Jackshaft type electric operator is designed for use on commercial and industrial
size sectional overhead doors and rolling doors only.

HEADROOM REQUIREMENT

SIDE ROOM REQUIREMENT

CONTROL

DOOR TYPE

ADJUSTABLE FRICTION CLUTCH

REDUCTION

OVERLOAD PROTECTION

DOOR TRAVEL

LIMIT SWITCHES

Side mount below door shaft, no additional headroom
required. Operator mounted above door shaft,
requires 32 inches above hardware headroom. See
Fig. 1, Page 4.

Requires 26 inches of side clearance out from jamb.
See Fig. 1, Page 4.

24 volt secondary control circuit as standard.

For use on lift clearance and vertical lift sectional
over-head doors requiring over 30 inches of headroom,
and rolling doors.

Provided to protect door and operator if door movement
is obstructed.

Worm gear running in oil bath. 40 to 1 ratio. Output
speed is approximately 43 RPM. Secondary reduction
is chain and sprocket.

Manual reset type for over current protection.

Operator to move door 6 to 12 inches per second.
Depending on door size, sprocket reduction and
track type.

Chain drive, screw type.

5973132-2

Under the terms of this limited warranty, for any operator components that are found to be defective upon inspection by
authorized Raynor personnel, Raynor will, at its option, repair or replace the defective door components. Labor charges for
installations or repairs shall be the responsibility of the consumer and must be performed by an authorized Raynor Dealer.

This warranty extends only to the original purchaser. This warranty is not transferable.

Raynor shall not be liable for any consequential or incidental damages.

Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above limitation or
exclusion may not apply to you.

Claims for defects in material and workmanship covered by this warranty shall be made in writing with proof of purchase
to the dealer from whom the product was purchased or call Raynor at 1-800-4-RAYNOR within the warranty period. Raynor

may choose to have the product returned for inspection.
This warranty gives you specific legal rights. You may also have other rights, which may vary from state to state.

This warranty applies only to doors that are professionally installed by an authorized Raynor Dealer.

This warranty does not apply to any damage or deterioration caused by abuse or failure to provide reasonable and
necessary maintenance.

ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY,
ARE HEREBY EXPRESSLY EXCLUDED.

MOTOR

FREQUENCY OF OPERATION

Continuous duty rated, NEMA "C" faced, 1725 RPM.

Will handle up to 30 cycles per hour or 300 cycles per
day.

Raynor warrants the electrical operator and component parts against defects in material and workmanship for three (3)
years, on the operator only, when purchased with any model of Raynor commercial sectional or rolling door.

Raynor warrants the electrical operator and component parts for two (2) years against defects in material and workmanship.

Summary of Contents for COH



















Reviews: