background image

27

The door should be fully 
closed if possible. Pull 
down on the emergency 
release handle and lift 
the door manually. To 
reconnect the door to the 
opener, press the door 
control push bar.

The 

lockout feature

 

prevents the trolley from 
reconnecting automatically. 
Pull the emergency release 
handle down and back 
(toward the opener). The 
door can then be raised and 
lowered manually as often 
as necessary. To disengage 
the lockout feature, pull 
the handle straight down. 
The trolley will reconnect 
on the next UP or DOWN 
operation, either manually 
or by using the door control 
or remote.

To prevent possible SERIOUS INJURY or DEATH from 
a falling garage door:
•  If possible, use emergency release handle to 

disengage trolley ONLY when garage door is 
CLOSED. Weak or broken springs or unbalanced 
door could result in an open door falling rapidly 
and/or unexpectedly.

•  NEVER use emergency release handle unless 

garage doorway is clear of persons and 
obstructions.

•  NEVER use handle to pull door open or closed. If 

rope knot becomes untied, you could fall.

Lockout position

Manual disconnect position

Using the Wall-Mounted Door Control

THE MULTI-FUNCTION DOOR CONTROL

Press the push button to open 
or close the door. Press again 
to reverse the door during the 
closing cycle or to stop the door 
while it's opening.

Light feature

Press the Light button to turn 
the opener light on or off. It will not control the opener 
lights when the door is in motion. If you turn it on and 
then activate the opener, the light will remain on for 4-1/2 
minutes. Press again to turn it off sooner. The 4-1/2 
minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2 
minutes as follows: Press and hold the Lock button until 
the light blinks (about 10 seconds). A single blink indicates 
that the timer is reset to 1-1/2 minutes. Repeat the 
procedure and the light will blink twice, resetting the timer 
to 2-1/2 minutes. Repeat again for a 3-1/2 minute interval, 
etc., up to a maximum of four blinks and 4-1/2 minutes.

Lock feature

Designed to prevent operation of the door from 
hand-held remote controls. However, the door will open 
and close from the Door Control, the Outside Keylock and 
the Keyless Entry Accessories.

To activate, press and hold the Lock button for 2 seconds. 
The push bar light will fl ash as long as the Lock feature 
is on.

To turn off, press and hold the Lock button again for 
2 seconds. The push bar light will stop fl ashing. The Lock 
feature will also turn off whenever the “learn” button on 
the motor unit panel is activated.

Additional features when used with the 3-Button 
hand-held remote

A) To control the opener lights:

In addition to operating the door, you 
may program the remote to operate 
the lights.

1.  With the door closed, press and hold a small remote 

button that you want to control the light.

2.  Press and hold the Light button on the Multi-Function 

door control.

3.  While holding the Light button, press and hold the Lock 

button on the door control.

4.  After the opener lights fl ash, release all buttons.

B) To operate one door using all three buttons on the 
hand-held remote:

You may program the remote to 
open the door with the large button, 
close it with the middle button, and 
stop the door’s movement with the 
third button.

NOTE: 

If remote is already programmed, you must fi rst 

erase all codes. See Programming.

1.  With the door closed, press and hold the large 

remote push button.

2.  Press and hold the Lock button on the door control.

3.  Press and hold the door control push bar.

4.  After the opener lights fl ash, release all buttons.

Using Your Garage Door Opener (Continued)

S

AFETY

 S

IGNAL

™ light feature:

 Lights will also turn on 

when someone walks through the open garage door. 
With a Multi-Function Door Control, this feature may be 
turned off as follows: With the opener lights off, press and 
hold the light button for 10 seconds, until the light goes 
on, then off again. To restore this feature, start with the 
opener lights on, then press and hold the light button for 
10 seconds until the light goes off, then on again.

Push 
Button

Lock 
Button

Light 
Button

To Open the Door Manually

Open

Stop

Close

Trolley
Release
Arm

Trolley
Release
Arm

Emergency
Release
Handle
(Pull Down)

Emergency
Release Handle
(Down and Back)

Summary of Contents for 3270RGD





































Reviews: