manualshive.com logo in svg

Raymarine RayTech RNS 5.0, User Manual

Share
Download
Raymarine RayTech RNS 5.0 User Manual Download Page 151

 

143

 Appendix F: Glossary of terms

            

Term Meaning

Definition

Awa

Apparent wind angle

The angle of wind as measured by your vessel’s instruments. When the 
boat is stationary, Awa is equal to True wind angle (Twa). When the 
boat moves, Awa is always less than Twa. Measured in degrees.

Aws

Apparent wind speed

The speed of wind as measured by your vessel’s instruments. When 
sailing upwind, Aws is always greater than True wind speed (Tws). 
When sailing downwind, Aws is always less than Tws. Measured in 
knots.

Twa

True wind angle

The angle between True wind direction (Twd) and he centerline of the 
vessel. Measured in degrees.

Tws

True wind speed

The velocity of the wind relative to the surface of the water. Measured 
in knots.

Twd

True wind direction

The magnetic direction that the wind is coming from, calculated to 
appear as though measured from a stationary boat. Measured in 
degrees.

Active route

The route on the chart which is being used for navigation.

Vmg

Velocity made good

The vessel’s speed towards or away from the Twd, used to measure the 
performance relative to upwind/ downwind targets.

Tab

Rudder tab

An adjustable section of the rudder that allows the rudder to be cor-
rected for lee or weather helm as appropriate. Measured in degrees.

Summary of Contents for RayTech RNS 5.0

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands