background image

2

Universal I/O Drive - Installation Guide

Important information

Safety notices

WARNING:

Product installation

This equipment must be installed and operated in accordance 
with the instructions contained in this handbook. Failure to do so 
could result in poor product performance, personal injury and/
or damage to your boat. 

Because correct performance of the boat’s steering is critical for 
safety, we STRONGLY RECOMMEND that an Authorized 
Raymarine Service Representative fits this product. 

WARNING:

Navigation aid

Although we have designed this product to be accurate and 
reliable, many factors can affect its performance. As a result, it 
should only be used as an aid to navigation and should never 
replace commonsense and navigational judgement. Always 
maintain a permanent watch so you can respond to situations as 
they develop. 

EMC conformance

All Raymarine equipment and accessories are designed to the best 
industry standards for use in the recreational marine environment. 
The design and manufacture of Raymarine equipment and 
accessories conform to the appropriate Electromagnetic 
Compatibility (EMC) standards, but correct installation is required to 
ensure that performance is not compromised. 

Handbook information

To the best of our knowledge, the information in this handbook was 
correct when it went to press. However, Raymarine cannot accept 
liability for any inaccuracies or omissions it may contain. In addition, 
our policy of continuous product improvement may change 
specifications without notice. As a result, Raymarine cannot accept 
liability for any differences between the product and the handbook. 

© Raymarine Ltd 2001.

All manuals and user guides at all-guides.com

Summary of Contents for E12026


















Reviews: