background image

Chapter 1 

Basic safety instructions 

RAYLASE 2-Axis Laser Beam Deflection Units 

MN051_v1.0.5 

1.5 

Laser area 

For the purposes of accident prevention, the laser area is defined as the area in which the 
maximum permitted radiation value can be exceeded. This is generally applicable for class 
3B, 3R and 4 lasers. For class 1 to 2M laser devices, a laser area can be produced by focus-
ing the laser beam. 

A sufficient beam intensity produces a laser area that covers the entire radiation angle of the 
deflection unit and includes the reflection from all objects that can be exposed to the radiation 
as a result. Note that even apparently diffuse surfaces can reflect laser radiation and a laser 
beam that has been reflected several times can still be dangerous. 

The laser area must be indicated by corresponding warning signs or lamps and protected by 
appropriate shading and interlock switches.  

No flammable or explosive objects or liquids should be located in the laser area. 

This operating manual interprets a selection of accident prevention regulations from the point 
of view of using laser deflection units in industrial plants. However, the applicable local and 
national standards, rules and regulations are binding. 

 

laser

shutter

RAYLASE
deflection unit

cover

reflected laser beam

deflected laser beam

working surface

Laser area

 

 

Summary of Contents for SUPERSCAN II-10



























Reviews: