RAYLASE AXIALSCAN Manual Download

Page: 14 / 71

Chapter 2

Basic information

RAYLASE 3-Axis Subsystems for Laser Beam Deflection

MN025 / v2.1.0

2.9

Status LEDs of the deflection unit

The status LEDs allow you to check important functions and statuses on the deflection unit. If
the deflection unit has status LEDs (depends on the type), they are located behind a protec-
tion window on the rear of the deflection unit.

For subsystems with analog interface only

2.9.1

Analog deflection units

LED arrangement

Name Color

Meaning

green

Position acknowledge-X

Data transfer when LEDs
are flickering. (not analyza-
ble)

green

Position acknowledge-Y

red

Error X

Galvanometer scanner or
driver electronics defective.
Power supply defective if
LEDs are flickering.

red

Error Y

D10

green

+VCC

Power supplies ready for
being used if LEDs are lit.

D11

green

-VCC

For subsystems with digital interface only

2.9.2

Digital deflection units

LED arrangement

Name Color

Meaning

red

CLK error

Data transmission faulty.
Cable defective.

red

Parity error X

red

Parity error Y

green

Temp. status X

Temperature status availa-
ble if LEDs are lit.

green

Temp. status Y

orange

New data X

New data is being trans-
ferred if status LEDs are lit.

orange

New data Y

red

Error X

Galvanometer scanner or
driver electronics defective.
Power supply defective if
LEDs are flickering.

red

Error Y

D10

green

+VCC

Power supplies ready for
being used if LEDs are lit.

D11

green

-VCC

Summary of Contents for AXIALSCAN








































































Search results

Summary of Contents for AXIALSCAN

Reviews:

Related manuals for AXIALSCAN

Brands by name

Popular brands

RAYLASE AXIALSCAN, Manual

Search results

Summary of Contents for AXIALSCAN

Reviews:

Related manuals for AXIALSCAN

Brands by name

Popular brands