Raycap ProSMS 8 Installation Manual Download Page 7

Page: 7 / 24

130 620 300 Rev.C 171116

Page 7 of 24

www.raycap.com

INSTALLATION MANUAL

ProSMS 8

5.1

Installation

Very high voltages are present on this ProSMS device.

Disconnect the PV Array and make sure all sources of power are locked out

before performing any work, removing or mounting the device.

For proper operation, external surge protection in combination with correct overcurrent fusing

must be provided in the combiner box where the device is installed, otherwise the ProSMS

device may be damaged. Overcurrent fusing should be installed on all string channels,

preferable on the negative side (ref. picture below).

The unit should be installed in an enclosure with at least IP5x (dust test) environmental rating

per IEC60529.

5.2

Device setting

Before powering device for the first time set device address and communication options as per the

ProSMS settings tables on page 13.

No reboot or removing/applying power is necessary for changes in settings or address to take

effect. ProSMS has an advanced built in mechanism that recognizes settings change and

sets internal parameters to match the settings immediately when settings are changed. This

also applies to baud rate and parity change.

CAUTION

VOLTAGE

DANGER

WARNING

NOTICE

CAUTION

VOLTAGE

DANGER

WARNING

NOTICE

CAUTION

VOLTAGE

DANGER

WARNING

NOTICE

CAUTION

VOLTAGE

DANGER

WARNING

NOTICE

CAUTION

VOLTAGE

DANGER

WARNING

NOTICE

(Insert #1)

Note: Only colors of the Central inverter can be changed if necessary. Please don’t change the

connection Lines colors anymore!!! It is important that is Red and Common - is Blue!

These two colors are common representation for positive and negative potential of a DC system!

Summary of Contents for ProSMS 8
























Search results

Summary of Contents for ProSMS 8

Reviews:

Related manuals for ProSMS 8

Brands by name

Popular brands

Raycap ProSMS 8, Installation Manual

Search results

Summary of Contents for ProSMS 8

Reviews:

Related manuals for ProSMS 8

Brands by name

Popular brands