background image

Right handlebar control switches 

1.   Electric starter switch – When this switch is pressed, starter motor cranks the engine. This 

switch should not be pressed over 5 seconds continuously.

2.   Hazard warning switch – All 4 indicators starts to flash. This button can be operated when you 

are a temporary obstruction for traffic or you   want to warn the upcoming vehicle about 
unusual condition up ahead.

3.   Headlamp switch – 

(a)  “     “ position –  The headlamp , front parking light and tail lamp are turned ON.
(b)  “    “  position –  All lamps are turned OFF.
(c)   “     ” position–  Front parking lamp and tail lamp are turned ON. 

Fuel tank & Fuel tank cap

The capacity of the fuel tank is 9L, including reserve fuel.
             (a)   Opening fuel tank cap - To open the fuel tank cap insert the key and rotate it 90° in 

clockwise direction, now fuel tank cap can be taken out.

(b)  Closing fuel tank cap - To close fuel tank cap, align the latch on the tank cap with the 

groove on the oil filling neck, press the cover down, now take out the key.

(c)   Fuel filling – Make sure that tank is not over filled. The gasoline is inflammable, so 

engine should be stopped before fuel filling. Fuel filling should not be done near fire 
and don't smoke while fuel filling.

3

1

2

(7)

Summary of Contents for RY-125PRO























Reviews: