background image

  Th is manual is intended only for use by a qualifi ed heating installer/technician. Read and follow this manual, all supplements and related 

instructional information provided with the boiler. Install, start and service the boiler only in the sequence and methods given in these 
instructions. Failure to do so can result in severe personal injury, death or substantial property damage.

 

Do not use the boiler during construction.

 Construction dust and particulate, particularly drywall dust, will cause contamination of 

the burner, resulting in possible severe personal injury, death or substantial property damage.  Th

  e boiler can only be operated with a dust-

free air supply. Follow the instruction manual procedures to duct air to the boiler air intake. If the boiler has been contaminated by operation 
with contaminated air, follow the instruction manual guidelines to clean, repair or replace the boiler if necessary.

 Affi  x these instructions near to the boiler/water heater. Instruct the building owner to retain the instructions for future use by a qualifi ed 

service technician, and to follow all guidelines in the User’s Information Manual.

P/N 42-9472 Copyright 2008 Mestek, Inc.

Cast iron condensing boiler

Cast iron condensing boiler

Control manual

Control adjustment and
operation instructions

Control manual

Control adjustment and
operation instructions

Also read and follow:

200

i

 

Boiler manual

200

i

 Vent/air manual

Also read and follow:

200

i

 

Boiler manual

200

i

 Vent/air manual

M2i-CM-1

200i

200i

Summary of Contents for 200i

































Reviews: