Raveon RV-M7 Technical Manual Download Page 5 | Manualshive

Page: 5 / 67

Raveon RV-M7 Technical Manual Download Page 5

RV-M7 Technical Manual

5

Potentially Explosive Atmospheres

Turn off your radio prior to entering any area with a potentially explosive atmosphere. Do not install
this product for use in areas with potentially explosive atmospheres. Do not remove, install, or charge
batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire
resulting in bodily injury or even death.

Note

:

The areas with potentially explosive atmospheres referred to above include fueling areas such as

below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains
chemicals or particles, such as grain, dust or metal powders, and any other area where you would
normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are
often but not always posted.

1.4 Safety Training information:

Antennas used for this transmitter must not exceed an antenna gain of 0 dBd. The radio modem must
be used in fixed vehicle-mount configurations or at fixed base-station sites. It is not intended for
portable applications.

This radio is restricted to occupational use, work related operations only where the radio operator must
have the knowledge to control the exposure conditions of its passengers and bystanders by maintaining
the minimum separation distance of following range. Failure to observe these restrictions may result in
exceeding the FCC RF exposure limits.

Antenna Installation

For rear deck trunk installation, the antenna must be located at least the following range away from rear
seat passengers and bystanders in order to comply with the FCC RF exposure requirements.

For model

RV-M7-UC

:

Radiated frequency and Distance

RV-M7-UC (450-480MHz 5 watts)

1.97 Feet (0.6 m)

FCC ID: SRS-RV-M7-UC

Raveon Technologies Corporation

For model

RV-M7-VB

Radiated frequency and Distance

RV-M7-VB (150-174MHz 5 watts)

90cm

FCC ID: SRS-M7-VB

Raveon Technologies Corporation

For vehicular roof top installation, the antenna must be placed in the center of the roof.

1.5 Certifications

The following certifications are specific to models RV-M7-Vx:

Electromagnetic Compatibility and Radio Spectrum Matters (ERM):

«
...
3
4
5
6
7
...
»

Summary of Contents for RV-M7




































































Reviews:

No comments