manualshive.com logo in svg

Ravenheat CS 80 T, Instructions For Use Installation And Servicing

Introducing the Ravenheat CS 80 T - a top-of-the-line heating solution for your home. Ensure optimal performance with our comprehensive Instructions For Use Installation And Servicing manual. Download it for free from our website manualshive.com, and unlock the full potential of your Ravenheat CS 80 T with ease.

Share
Download
background image

      

3

HIGH EFFICIENCY CONDENSING BOILER

 EFFICIENCY CONDENSING BOILER

FOR CENTRAL HEATING AN

FOR CENTRAL HEATING AND DOMESTIC HOT WATER

This new highly effi cient turbo-modulating boiler is designed to meet domestic hot water and central heating requirements at 
super high effi ciency.

POSITION

The appliance is extremely versatile as it can be fi tted in almost any room. The appliance is room sealed so there is no contact 

between the combustion chamber and living accommodation. This guarantees maximum safety and effi ciency. Each boiler 
has been designed and manufactured in our modern plant to exacting ISO 9001 discipline, all boilers carry full CE marking of 
approval. Technical sales and commercial services are available throughout the UK Mainland. This product is guaranteed by 
Ravenheat manufacturing ltd, Chartists Way, Morley, LEEDS, LS27 9ET. Telephone No (0113) 252 7007.

Guarantee is a full 12 months from date of purchase providing the appliance has been fi tted in accordance with these instructions 

and relevant codes of practice.

  

- 

Gas valve.

Gas valve.

- 

Variable head pump suitable for any type of central heating system.

- 

Variable head pump suitable for any type of central heating system.

- 

Burner with fl ame stabiliser designed to operate under all thermal conditions.

- Burner 

with 

fl ame stabiliser designed to operate under all thermal conditions.

- 

Unique 

- Unique 

condensing heat exchanger

condensing heat exchanger

 for high thermal fl ue transfer from gases to water.

 for high thermal fl ue transfer from gases to water.

- 

Stainless steel plate heat exchanger for super high heat transfer to domestic hot water supply.

- 

Stainless steel plate heat exchanger for super high heat transfer to domestic hot water supply.

- 

Built in frost protection.

- 

Built in frost protection.

 - 

Printed circuit board designed to connect to room stat and/or timer. 

 - 

Printed circuit board designed to connect to room stat and/or timer. 

-                          Aesthetically pleasing panels and controls.

-                          Aesthetically pleasing panels and controls.
- 

On/Off ball valves for shutting off gas, central heating and domestic hot water circuit.

- 

On/Off ball valves for shutting off gas, central heating and domestic hot water circuit.

-                          Safety relief valve (for safety discharge).

-                          Safety relief valve (for safety discharge).
-                          Programmable 7 day module with digital display (time clock version only).

-                          Programmable 7 day module with digital display (time clock version only).

NOTE: Due to the high effi ciency  of  thi

effi ciency of this boiler a plume of water vapour will form at the fl ue 

terminal during operation.

COSHH - CONTROL OF SUBSTANCES HAZARDOUS  TO HEALTH

 HAZARDOUS  TO HEALTH

IMPORTANT

IMPORTANT

It is the Users/Installers responsibility to ensure that the necessary personal protective clothing is worn when 
handling this appliance, and where applicable the pertinent parts that contain any materials that could be interpreted 
as being injurious to health and safety.

GENERAL INFORMATION:
GLUES AND SEALANTS - exercise caution - if these are still in liquid form.
RAVENHEAT use only high quality material for production of this product, in an effort to protect the environment 
wherever  possible components should be recycled.

WARNING: when installing the appliance, care should be taken to avoid any possibility of injury when handling sheet 
metal parts.

MAJOR COMPONENTS

Summary of Contents for CS 80 T




































































Reviews:

No comments

Related manuals for CS 80 T

Raypak 1001 Operating And Installation Manual preview
1001
Brand: Raypak Pages: 76
hajdu ZA15 Quick Start Manual preview
ZA15
Brand: hajdu Pages: 6
U.S. Boiler Company ALTA-080 Installation, Operating And Service Instructions preview
ALTA-080
Brand: U.S. Boiler Company Pages: 104
Nieco BroilVection JF63 Gas Owner'S Manual preview
BroilVection JF63 Gas
Brand: Nieco Pages: 40
Ideal Boilers i 35 Installation & Servicing Instructions Manual preview
i 35
Brand: Ideal Boilers Pages: 72
Eco Engineering Easypell Installation Manual preview
Easypell
Brand: Eco Engineering Pages: 104
Blue Flame BFRB-24 Installation & Operation Manual preview
BFRB-24
Brand: Blue Flame Pages: 16
Weil-McLain PD Gas Series 3 Installation Instructions Manual preview
PD Gas Series 3
Brand: Weil-McLain Pages: 6
Glow-worm ultracom hxi Instructions For Use Manual preview
ultracom hxi
Brand: Glow-worm Pages: 12
Ideal Boilers FF 330-360 User Manual preview
FF 330-360
Brand: Ideal Boilers Pages: 4
Vaillant Air flue duct Installation Instructions Manual preview
Air flue duct
Brand: Vaillant Pages: 52
Knight 106 Service Manual preview
106
Brand: Knight Pages: 48
Nibe EKS 750 User'S And Installer'S Manual preview
EKS 750
Brand: Nibe Pages: 44
Ferroli ATLAS D 30 K 100 Instructions For Use, Installation And Maintenance preview
ATLAS D 30 K 100
Brand: Ferroli Pages: 100
Rinnai M Series Installation And Operation Manual preview
M Series
Brand: Rinnai Pages: 122
Viadrus Hercules U 24 Manual For Operation And Installation preview
Hercules U 24
Brand: Viadrus Pages: 32
Potterton NXR4 Installation, Operation & Maintenance Manual preview
NXR4
Brand: Potterton Pages: 43
Ideal Heating LOGIC MAX HEAT2 H12 User Manual preview
LOGIC MAX HEAT2 H12
Brand: Ideal Heating Pages: 8

Brands by name

Popular brands

Load more brands