background image

While every effort has been made to ensure the accuracy of this document, 

Raven Industries assumes no responsibility for omissions and errors. Nor is any 

liability assumed for damages resulting from the use of information contained 

herein.

Raven Industries shall not be responsible or liable for incidental or consequential 

damages or a loss of anticipated benefits or profits, work stoppage or loss, or 

impairment of data arising out of the use, or inability to use, this system or any of 

its components. Raven Industries shall not be held responsible for any 

modifications or repairs made outside our facilities, nor damages resulting from 

inadequate maintenance of this system.

As with all wireless and satellite signals, several factors may affect the availability 

and accuracy of wireless and satellite navigation and correction services (e.g. 

GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the 

accuracy, integrity, continuity, or availability of these services and cannot 

guarantee the ability to use Raven systems, or products used as components of 

systems, which rely upon the reception of these signals or availability of these 

services. Raven Industries accepts no responsibility for the use of any of these 

signals or services for other than the stated purpose.

Disclaimer

©Raven Industries, Inc. 2014, 2015

Summary of Contents for SmarTrax MD





































Reviews: