manualshive.com logo in svg

Raven SmarTrax John Deere 8770, Installation Manual

Share
Download
Raven SmarTrax John Deere 8770 Installation Manual Download Page 7

CHAPTER

2

Manual No. 016-5034-020 Rev. B

3

Chapter 2

Introduction

Congratulations on your purchase of the Steering Ready system! This system is designed to provide cutting-
edge, hands-free steering of the machine via Global Positioning System (GPS) coordinates.

This manual applies to the following machines:

MAKE:  John Deere
MODEL: 8X60/8X70

FIGURE 1.

John Deere 8770

Preparing for Installation

Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the 
machine and leave it turned off for the duration of the installation process. Bleed pressure from the hydraulic 
system by loosening the hydraulic fittings slowly, where applicable.

During the installation process, follow good safety practices. Be sure to carefully read the instructions in this 
manual as you complete the installation process.

Summary of Contents for SmarTrax John Deere 8770

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands