background image

RAVEN  INDUSTRIES

LIMITED  WARRANTY

WHAT IS COVERED?

This warranty covers all defects in workmanship or materials in your Raven
Flow Control Product under normal use, maintenance, and service.

HOW LONG IS THE COVERAGE PERIOD?

This warranty coverage runs for 12 months from the purchase date of your
Raven Flow Control Product.  This warranty coverage applies only to the
original owner and is not transferrable.

HOW CAN YOU GET SERVICE?

Bring the defective part, and proof of date of purchase, to your local dealer.
If your dealer agrees with the warranty claim, he will send the part, and proof
of purchase to his distributor or to Raven for final approval.

WHAT WILL RAVEN INDUSTRIES DO?

When our inspection proves the warranty claim, we will, at our option, repair
or replace the defective part and pay for return freight.

WHAT DOES THIS WARRANTY NOT COVER?

Raven Industries will not assume any expense or liability for repairs made
outside our plant without written consent.  We are not responsible for damage
to any associated equipment or product and will not be liable for loss of profit
or other special damages.  The obligation of this warranty is in lieu of all other
warranties, expressed or implied, and no person is authorized to assume for
us any liability.  Damages caused by normal wear and tear, mis-use, abuse,
neglect, accident, or improper installation and maintenance are not covered
by this warranty.

Summary of Contents for PRECISION AUTOBOOM G1

















Reviews: