manualshive.com logo in svg

Raven 47860A-600, User Manual

Share
Download
Raven 47860A-600 User Manual Download Page 8

 

Raven Electronics Corporation

 

 4655 Longley Lane 

 Reno, NV 89502 

Page 7 of 10 

2.3 

I/O’s 

Refer to Figure 2-1 for a picture of the I/O locations. 

I/O Pin 

Description 

Default: Open/Closed 

1 - 6 

Vote Indication, ports 1-6 

Open (Closed if Voted) 

7-12 

Receiver Fault, ports 1-6 

Open (Closed if Faulted) 

13 

Ethernet Link Up/Down 

Open, if Down 

14 

Unused 

 

15 

System Power 

Closed (Open if Power is Off) 

 

 

2.4  LED Status Indicators 

As shown in Figure 2-

2, there are seven LED’s.  One for the transmitter and one for each receiver port.  The LED’s 

change colors to indicate the status of a particular port.  There are four possible LED states. 

 
Transmitter Status LED Status Indicator 

(refer to Figure 2-2) 

 

Off

 = Idle 

Red

 = Transmit 

 

 
Voter Receiver Status LED Status Indicators 

(refer to Figure 2-2)

 

 

Red =

 Fault (RCVR) 

This indicates a receive port fault.  A fault condition can exist if a receiver port goes to un-squelch (loss of status 
tone or COR detect) but no audio is detected for a period of time indicating a fault condition.  For the transmitter 
port the red LED indicates TX activity.   

Green

 = Receive 

This indicates a receive port has gone to the un-squelch condition (status tone drops or COR detected).  There 
is no green state indicator for the transmitter port. 

Blue 

= Voted 

This indicates a receive port is voted.  There is no blue state indicator for the transmitter port. 

Off

 = Idle  

This  indicates  a  squelch  status  (status  tone  being  detected  or  no  COR  detected)  on  a  receiver  port.    For  the 
transmitter port this indicates no TX activity. 

 

 

Figure 2-2: RVI-600 Front Panel

 

Summary of Contents for 47860A-600












Reviews:

No comments

Brands by name

Popular brands

Load more brands