INSTRUCTION, USE AND
MAINTENANCE MANUAL
GB
Page 9 of 60
3.1
Residual risks
The machine was subjected to a complete analysis of
risks according to reference standard EN ISO 12100.
Risks are as reduced as possible in relation with tech-
nology and product functionality.
This manual stresses possible residual risks, also
highlighted in pictograms on the present manual and
adhesive warning signals placed on the machine: their
location is represented in “PLATE LOCATION ON MA-
CHINE INFORMATION TABLE” on page 5.
4.0 GENERAL SAFETY RULES
• Any tampering with or modification to the machine
not previously authorized by the manufacturer ex-
empts the latter from all responsibility for damage
caused by or derived from said actions.
• Removing of or tampering with the safety devices or
with the warning signals placed on the machine leads
to serious dangers and represents a transgression of
European safety rules.
• Use of the machine is only permitted in places free
from
explosion
or
fire
hazard and in
dry places
under cover
.
• Original spare parts and accessories should be used.
THE MANUFACTURER DENIES
ANY RESPONSIBILITY IN CASE
OF DAMAGES CAUSED BY UNAU-
THORIZED MODIFICATIONS OR
BY THE USE OF NON ORIGINAL
COMPONENTS OR EQUIPMENT.
• Installation must be conducted only by qualified
personnel exactly according to the instructions that
are given below.
• Ensure that there are no dangerous situations dur-
ing the machine operating manoeuvres. Immediately
stop the machine if it miss-functions and contact the
assistance service of an authorized dealer.
• In emergency situations and before carrying out any
maintenance or repairs, disconnect all supplies to
the machine by using the main switch.
• The machine electrical supply system must be
equipped with an appropriate earthing, to which
the yellow-green machine protection wire must be
connected.
• Ensure that the work area around the machine is free
of potentially dangerous objects and that there is no
oil since this could damage the tyre. Oil on the floor
is also a potential danger for the operator.
RAVAGLIOLI S.p.A.
7300-M018-2_R
G8945.26 - G8945IT.26 - G8945V.26 - G8945ITV.26 - G8945V.26S - G8945ITV.26S - G8945D.26 - G8945ITD.26 - G8945D.26S - G8945ITD.26S
3.0 SAFETY DEVICES
PERIODICALLY, AT LEAST MONTH-
LY, CHECK THE INTEGRITY AND
THE FUNCTIONALITY OF THE
SAFETY AND PROTECTION DE-
VICES ON THE MACHINE.
All the machines are equipped with:
• “man-operated” controls
(immediate stop of opera-
tion when the control is released) for all operating
devices;
• mandrel rotation;
• tool translation;
• bead breaking roller translation;
• side bead breaking;
• lifting device (only for G8945V.26S - G8945ITV.26S
- G8945D.26S - G8945ITD.26S models);
• fixed protections and guards.
The machine is fitted with a number of fixed guards
intended to prevent potential crushing, cutting and
compression risks.
These protections have been realized after risks
evaluation and after all machine operative situations
have been considered.
All protections, specially the rubber ones, have to be
periodically checked in order to evaluate their wear
state.
PERIODICALLY CARRY OUT THE
MAINTENANCE OF THE PROTEC-
TIONS, SHELTERS AND SAFETY
DEVICES IN GENERAL, AS INDI-
CATED IN CHAPTER 13. ROUTINE
MAINTENANCE.
• Motor protection devices (only for G8945D.26
- G8945ITD.26 - G8945D.26S - G8945ITD.26S
models)
The new “Invemotor” motor is equipped with elec-
tronic protection devices. They stop the motor if
working defected conditions appear to avoid that the
motor itself can be damaged and that the operator
safety can be compromised (overvoltage, overload,
overtemperature). For other details, see the chapt.
14 “Fault-Finding”.
• Non-adjustable pressure limiter.
This allows inflation of tyres in reasonable safety.
Inflation of tyres to over 4,2 ± 0,2 bar (60 PSI) is
not allowed.
