background image

NKI1480B DAX60 and DAX120 Amplifiers—Installation

Page 18 of 18 (Jul-98)

All material returned to Rauland-Borg Corporation under this warranty must be
accompanied with information concerning the nature of the defect, the original date
of shipment, original invoice number, and, if a defective component, the model
number of the unit from which it was removed.

This warranty is in lieu of all other agreements arid warranties, general or special,
expressed or implied, and no representative or person is authorized to assume for us
any other liability in connection with the sale or use of our products.

Service Policy

The entire Rauland-Borg organization is interested in the proper maintenance of
your equipment for as long as you own it. Our national network of Rauland-Borg
distributors is at the service of all purchasers of our products.

Should you have a problem with your equipment, or require any advice or
assistance, contact your local Rauland-Borg distributor. If you are not able to locate
a local Rauland-Borg distributor, the information or action that you want can be
obtained by writing to our Sales Engineering Department, at the address shown
above.

No end-user replaceable components are contained within this equipment. Refer
servicing to your local Rauland-Borg distributor.

Important:

Any attempt at self-service of this equipment may result in exposure to electrical
shock, or in extensive damage to the equipment and possible voiding of the
equipment warranty.

Summary of Contents for DAX60



















Reviews: