RASOR Optima 702 Use Manual Download Page 8

8.  USE WARNINGS

We recommend following the indications below in order to always work in safety conditions.

·

All  the  operations  must  be  carried  out  complying  strictly  with  the  safety  rules  of  the

country  where  the  device  is  sold.

·

It is STRICTLY FORBIDDEN to smoke during the installation or adjustment operations of
the electric scissors.

·

The Customer undertakes to comply with and make his staff observe all the rules and
regulations  in  force  concerning  safety,  prevention  of  accidents  and  health  in  the  work

place. Therefore, the Customer assumes the responsibility to strictly follow all the rules

and  regulations  in  force,  as  well  as  the  special  provisions  in  force  in  sport  and  public

installations  the  Customer  declares  to  know  after  receiving  all  the  relative  necessary
pieces of information.

·

The  electric  scissors  work  also  without  their  safety  protective  device.  This
protective device must NEVER be removed.

·

Always  check  the  resistance  of  the  material  to  be  cut  and  the  kind  of  blade  which  is

being  used.

·

The Customer shall equip his own personnel with all the individual safety protections for

the execution of the works, as well as with the ones which might be prescribed by the
Manufacturer  due  to  specific  danger  conditions  of  the  plant  or  of  the  area  where  the

personnel  must  work.

·

Only  one  operator  must  use  the  electric  scissors  always  standing  behind  the  guide
handle.  Do  not  make  any  adjustment  while  the  blade  is  working  or  while  the  electric

plug  is  connected.

·

Always  pay  attention  to  the  electric  cable  position  to  prevent  it  from  being  cut  or
damaged  by  the  blade.

·

It is allowed to assemble electric scissors OPTIMA 702 on machines O.E.M. on condition
that their original structure is not modified. Otherwise, the intervention must be certified

by Rasor

®

.

9.  RESIDUAL RISKS

Even though the electric scissors are safe, operators must pay attention to preserve their

and  other  people’s  safety.

L

At  the  end  of  the  working  operations,  the  motor  could  be  very  hot.

L

The  cutting  blade  can  work  even  when  the  protective  device  is  disassembled.

Enfocus Software - Customer Support

EN

24

Summary of Contents for Optima 702
















Reviews: