background image

8

EN

9. RESIDUAL RISKS

Even though the cutting unit is safe, operators must pay attention to preserve their and

other people’s safety.

The cutting blade can work even when the protective device is disassembled.

8. USE WARNINGS

We recommend following the indications below in order to always work in safety conditions.

All the operations must be carried out complying strictly with the safety rules of the

country where the fixture is sold.

It is STRICTLY FORBIDDEN to smoke during the installation or adjustment operations of

the cutting unit.

The Customer undertakes to comply with and make his staff observe all the rules and

regulations in force concerning safety, prevention of accidents and health in the work

place. Therefore, the Customer assumes the responsibility to strictly follow all the rules and

regulations in force, as well as the special provisions in force in sport and public installations

the Customer declares to know after receiving all the relative necessary information.

The cutting unit works also without their safety protective device. This protective

device must NEVER be removed.

Always check the resistance of the material to be cut and the kind of blade which is being

used.

The Customer shall equip his own personnel with all the individual safety protections for

the execution of the works, as well as with the ones which might be prescribed by the

Manufacturer due to specific danger conditions of the plant or of the area where the

personnel must work.

Do not carry out any adjustment while the blade is working.

Always pay attention to the position of the air pipe to prevent it from being cut or

damaged by the blade.

It is possible to assemble cutting unit FP861A2 on machines O.E.M. only if their original

structure is not modified. Otherwise, the intervention must be certified by Rasor

®

.

10. INSTALLATION AND USE

To install and use the cutting unit do as follows:

1) Fix the cutting unit to the machine by means of a flat or

angle bracket to mount on the upper part of the motor

support of the unit.

NOTE

The cutting unit can be installed in any position or angle: vertical,

uside down, lateral. The aluminium base does not have to touch

the machine table.

2) Lay down the material to be cut;

3) Connect the air hose to quick connection “A” (not supplied)

(see picture 3);

3

A

Summary of Contents for FP861A2
















Reviews: