ACXF55-30500
NOISE CONSIDERATION
Select an installation location that can support the weight of the air
conditioner and one that will not cause increased operating noise
and vibration.
Ensure that when installed, airflow and noise from the rear side of the
unit (outdoor) do not disturb neighbouring elements.
Obstacles placed in front of the air outlet on the rear side of the unit
(outdoor), or covers placed over it will cause excessive noise and
deterioration in performance.
TRANSFERRING
Repositioning or transfer of the air conditioner due to renovation or moving requires an additional service
charge. Please consult your dealer before moving.
AIR CONDITIONER OPERATION
OPERATING THE UNIT
Start operation by pressing OPERATION.
The operation will turn on and the display panel will light up.
To stop the operation, press the OPERATION again.
The unit will stop operating and the display panel light will turn off.
SETTING DISPLAY TEMPERATURE
OFTH0810-00
Printed in Philippines
5
8
BEFORE CALLING FOR SERVICE
Check the following points before calling for repairs or service.
If the malfunction persists, please contact Shun Hing Electric Service Centre Ltd.,
If the unit is too noisy during
operation.
If water drips off the rear of the
unit.
If water drips inside the room.
Humidity is high.
Condensed water is overflowing.
To rectify the problem, mount an optional drain
pan to the unit.
The following sounds are normal during operation:
A low humming sound indicating that the unit is operating.
A splashing sound indicating condensation in the condenser
coil.If you hear other noises, please consult
Shun Hing Electric Service Centre Ltd.,
A flowing sound due to circulation of the refrigerant when
the compressor is turned on.
A soft clicking sound when the compressor turns on and off.
Condition
1
Condition
4
Condition
5
Condition
2
Condition
3
If the unit does not operate.
If the unit does not cool properly.
The main power cord is not plugged in.
The main circuit breaker has tripped.
Remote control batteries are weak.
The room is too big for the unit’ s capacity.
The ventilation lever is set to OPEN
The air circulation is impeded by curtains or furniture.
After 15 minutes of operation, it is normal for the temperature
difference between intake and outlet air to be more than 8°C
for cooling.
The unit is tilted inward. To rectify this, tilt the unit
slightly outward.
Mount the optional drain pan if you prefer.
The drain pan may be blocked.
Condition
6
To call Shun Hing Electric Service Centre Ltd.
IMMEDIATELY Turn off the power and contact
Shun Hing Electric Service Centre Ltd.
as soon as any of the following events occur.
The circuit breaker frequently trips or the fuse blows
regularly.
If water or foreign objects have accidentally entered the
air conditioner.
If there is abnormal sound during operation.
NOTE:
1. The enclosure opposing the room side is splash proof (IPX4).
2. Do not install this appliance in a laundry room or other
locations where water may drip from the ceiling, etc.
3. If the supply cord is damaged or need to be replaced, it must
be replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
Information for Users on Collection and Disposal of Old Equipment and used Batteries
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard
these items, please contact your local authorities or dealer and ask for the
correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case
it complies with the requirement set by the Directive for the chemical involved.
6
HELPFUL INFORMATION & ENERGY SAVING HINTS
HELPFUL INFORMATION
ENERGY SAVING HINTS
Auto Restart Control
Timer Setting
Operation will automatically resume under the previous operation mode.
If the unit was set to TIMER mode or SLEEP mode, operation will not resume automatically.
When power failure occurs, the timer setting is cancelled. Once power returns, reset timer.
Your air conditioner’ s cooling capacity should match your room size.
For health reason do not overcool your room.
Avoid direct sunlight and heat.
Keeping ventilation set to close keeps cool air in and hot air out.
Clean the air filter every 2 weeks. Regular cleaning of the air filter preserves efficiency.
PRE-SEASON INSPECTION
Is the discharged air cold?
Are the air intake and outlet vanes of the indoor and outdoor side obstructed?
Are the remote control batteries weak?
After 15 minutes of operation, it is normal for the temperature difference between intake and outlet air
to be more than 8
°
C for cooling.
RECOMMENDED INSPECTION
Usage over several seasons will reduce performance as the unit becomes dirty. A dirty unit may produce foul
odours and dust may clog the dehumidifying drainage. Seasonal inspection is recommended in addition to
regular cleaning. Consult Shun Hing Electric Service Centre Ltd.,
7
CARE AND MAINTENANCE
Always turn off the air conditioner and the main power supply before cleaning
the unit.
Switch off the power supply if the unit is not going to be used for a long period
of time.
Clean the cabinet, front grille with mild soap or detergent and lukewarm water.
NOTE: Do not dry the front panel or the air filter in direct sunlight.
(Exposure to direct sunlight may discolour deform the panel.)
If the air filter becomes clogged with dust, the cooling capacity will drop, and 6% of the electricity used to
operate the air conditioner will be wasted.
If the unit is extremely dirty, heat transfer is less Efficient and the unit may not cool effectively. Contact
Shun Hing Electric Service Centre Ltd. for an annual check. (Annual check is not covered by the warranty.)
Do not clean with benzene, thinner, scouring powder or cloth soaked in caustic chemicals.
The filter can be easily cleaned using a vacuum cleaner. Vacuum the front of the filter and then wash the
rear with water. If it is badly spoiled, wash with a mild household detergent.
The front intake grille can be easily removed for cleaning purposes (refer to Remove the front intake
grille procedures). Gently wash it with water and a sponge.
OFF / ON
SLEEP(Cooling mode)
SLEEP
●
This setting enables the human body to enter sleep and automatically adjust the
temperature to achieve sleep comfort and energy-efficient operation.
●
When the sleep button is pressed (or touch control panel sleep light on),
the air conditioner enters the sleep stroke. Press it again to cancel the sleep schedule.
●
After sleep is activated, the SLEEP LED is on, and pressing it again will cancel
the sleep mode (SLEEP LED is dim).
●
SLEEP mode is released when the machine is turned off.
Note: During sleep operation, in order to avoid over-cooling and over-heating, the temperature, air volume
and wind direction have nothing to do with the remote control settings and will be adjusted automatically.
If the user needs cannot be met, the temperature or air volume can be reset.
◆
After the body enters the sleep state, the temperature will be lost due to heat, so in the sleep mode, the
air conditioner will keep running for one hour or increase by 1°C after reaching the set temperature,
so that people have a comfortable sleeping environment.
SLEEP
SET TEMP
SLEEP MODE
60MIN
SLEEP MODE
START
OR REACH THE SET TEMP
CLOSE
↑+1℃
■The air conditioner blows out cold misty
air, and the indoor air comes into contact
with the cold air blown out of low
temperature to produce misty air.
■There seems to be a sound of running
water. This is the sound of the
refrigerant flowing inside the air
conditioner.
■Occasionally there is the sound of "GI-GA",
the expansion
and contraction
of the front leaf
window due to
temperature
changes.
SELECTING OPERATION MODE
SELECTING FAN SPEED
Press FAN SPEED selection button to choose fan speed level of the fan.
(The indicator will light up and a “beep” sound will indicate changing setting)
If air conditioner automatically selects COOL or DEHUMIDIFYING mode and
the fan speed is at AUTO speed, it will operate the “Self-cleaning” function to
clear the dust on Heat exchanger,(Defer air flow for 40 seconds or intermittently operate)
AUTO
FAN SPEED
ADJUSTING HORIZONTAL AIRFLOW DIRECTION
Press AIR SWING button to select air swing direction angle.
(The indicator will light up and a “beep” sound will indicate changing setting)
Press the upper button to adjust left and right airflow direction.
Press the lower button to stop AIR SWING.
AUTO
SET
AIR SWING
When the air conditioner is OFF:
Press the TIMER-OFF button to set the timer.
Press the same button until the preferred hour of operation is reached.
(The TIMER indicator light will blink to await for setting)
Press TIMER SET button to complete the setting. At this time, the TIMER indicator light is steady
instead of blinking.
NOTE:
it is unavailable to set ON TIMER and OFF TIMER simultaneously.
The timer figure will change according to the time remaining.
SETTING THE OFF TIMER
TIMER-OFF
SET
CANCEL OFF TIMER SETTING
Press the CANCEL button to cancel the timer setting. The TIMER indicator light will turn off.
However the temperature remains displayed.
TIMER
SLEEP
CANCEL
POWERFUL OPERATION
To reduce / increase the temperature quickly under cool mode/heat mode:
Press POWERFUL button, after powerful is selected, the operation will go on
for 4 hours, after that it will shift back to previous operation mode.
If you want to cancel this operation, press powerful button once more.
POWERFUL
QUIET
POWERFUL
QUIET OPERATION
To reduce / increase temperature quickly :
Press QUIET button.
If you want to cancel this operation, press QUIET button once more.
QUIET
POWERFUL
QUIET
Press MODE to select the desired operation.
(The indicator will light up and a “beep” sound will indicate changing setting)
AUTO mode
Air conditioners are automatically operated according to indoor and outdoor temperatures.
COOL mode
To set room temperature to your preference of cooling comfort.
HEAT mode
To set room temperature to your preference of heating comfort.
DRY mode
DRY mode unit operates at low fan speed to give a gentle cooling operation.
AUTO
COOL
DRY
HEAT
MODE
HZ series
Press MODE to select the desired operation.
(The indicator will light up and a “beep” sound will indicate changing setting)
AUTO mode
Air conditioners are automatically operated according to indoor and outdoor temperatures.
COOL mode
To set room temperature to your preference of cooling comfort.
DRY mode
DRY mode unit operates at low fan speed to give a gentle cooling operation.
AUTO
COOL
DRY
HU series
MODE
SETTING THE ON TIMER
When the air conditioner is ON:
Press the TIMER-ON button to set the timer.
Press the same button until the preferred hour of operation is reached.
(The TIMER indicator light will blink to await for setting)
Press TIMER SET button to complete the setting. At this time, the TIMER indicator light is steady
instead of blinking.
NOTE:
it is unavailable to set ON TIMER and OFF TIMER simultaneously.
The timer figure will change according to the time remaining.
TIMER-ON
SET
Press TEMP/TIMER▲or▼to set the display temperature.
The temperature can be set between 16°C and 30°C.
Recommended temperature: 26°C~28°C
NOTES:
●The latest set temperature will be stored and displayed when the air-con is ON.
Display will
change
according
to the setting.
Display will
change
according
to the setting.
TEMP
Squeaking noise during operation,
Squeaking noise after shutting down
(This is due to the expansion or contraction of the host
due to temperature changes)
The temperature difference between the blower outlet and the suction temperature under the
normal state of the machin:cooling 8
℃
or above, heating (Heat pump model) 14
℃
or above,is a normal phenomenon.
