background image

1

PHII 

        THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND FOLLOWED  

 

    

 

 

DURING BOTH INSTALLATION AND OPERATION 

 

 

 

               

WARNING:

 

Raritan Engineering Company, Inc. recommends that a qualified  person or electrician    

 

 

 

in the case of  P104E**,  install this product.  Equipment damage, injury to personnel or death    

 

 

could result from improper installation.  Raritan Engineering Company,  Inc.  accepts no responsibility  

 

 

or liability for damage to equipment, or injury or death to personnel,  that may result from improper  

 

 

installation oroperation of this product.

WARNING:

 

Hazard of Flooding

 

Any installation made below the waterline must have vented loops positioned 

properly and all hose connections should be double-clamped.  Both intake and discharge seacocks 

should always be in the closed position when the toilet is not in use.  Failure to do so may result in 

flooding, property damage and loss of life. 

 

 

 

 

 

 

 

WARNING:

 

DO NOT

 install in an area requiring Ignition Protected Devices.

  

DO NOT 

operate P104E** series toilets with handle in place, serious bodily injury may occur.

The PHII is a manually operated double action piston 

toilet. The PHII can be converted to its electrical 

counterpart by adding an electrical conversion kit 

part# P104E**

All models are suitable for use in conjunction with our  

US Coast Guard Certified Type I flow-thru Marine 

Sanitation Devices (MSD), Raritan’s Electroscan® 

and Purasan®. 

1-856-825-4900

www.raritaneng.com

Model and Serial # :

 INSTALLATION AND MAINTENANCE INSTRUCTIONS

** Specify voltage 12 or 24 VDC

Link to online 

Warranty 

Registration

L584v0222jlc

Summary of Contents for PHII













Reviews: