background image

6

PLUMBING

PLUMBING

WARNING:  HAZARD OF FLOODING

Toilets mounted at or below the waterline, at 

greatest angle of heel, and connected to a  Seacock/

Thru Hull Fitting(s) MUST have VENTED LOOPS 

installed in toilet discharge plumbing and between 

raw water intake pump and toilet bowl.  

Install vented loops per manufacturer’s instructions. 
Sea Water Models installed below the waterline 

MUST have a vented loop installed between the 

intake pump and the toilet bowl.  
Double clamp all below-waterline connections.
IMPORTANT

•  Fittings and 90° bends should be kept to a 

minimum.

•  In-Line  Strainer  may  be  installed  on  Sea 

Water Models per Installation Instructions.  

This will prevent clogs.

•  Discharging untreated sewage is forbidden in 

all U. S. waters within the three-mile limit.

•  Thru-hull  fittings  and  seacocks  must  be 

installed where they are easily accessible.

•  Use  only  quality  reinforced  hoses  such  as 

Raritan Saniflex (SFH)

•  Secure all hoses properly.

Waterline

Pressurized Freshwater Model Installed 

Above/below Waterline

Discharge

Pressurized Fresh-

water 

Source

Shut off Valve

Waterline

remote pump

Electroscan

Waterline

Discharge Seacock

Waterline

Discharge Vented 

Loop

Intake Vented Loop

Discharge 

Seacock

Intake Seacock

Electroscan

Pressurized Freshwater Model Installed 

below Waterline

Holding Tank

 

 

Residual Water in the Bowl

 

The Marine Elegance is equipped with an           

integral vent to maintain water in the bowl when 

the plumbing lines are routed downward  

(See FIG 4a and FIG 4b).  

 

 

The Smart Toilet Control (STC) is designed to 

add water at the end of the flush cycle. The toilet 

will not hold more than about 4” in the bowl. 

If any of the discharge hose runs higher than 

the internal integral vent, DO NOT REMOVE 

THE VENT CAP.  For vent to work properly  

in   downward installation, the vent cap must be 

removed (see FIG 5).

Remote Intake Pump Model Mounted  

below Waterline

 

To enable vent, remove Vent Cap (FIG 5).

 

Toilet Installed above waterline 

or above Treatment Device and 

or Holding Tank = Downward 

discharge flow 

Remove vent cap

Toilet installed below waterline 

or below Treatment Device 

and or holding Tank = Upward 

discharge flow 

Do not remove vent cap

FIG 3a

FIG 4a

FIG 5

L490  0720jlc                                                                                                             

Vent Cap

FIG 3b

FIG 3c

FIG 4b

Summary of Contents for Marine Elegance Toilet













Reviews: