EMX Quick Setup Guide
9
QSG-EMX-1A-v3.3.10-E
255-80-6106-00 RoHS
To set or
enable
Use this command
IPv4
configuration
method
network ipv4 interface WIRELESS
configMethod <mode>
<mode> =
dhcp
(default) or
static
IPv6
configuration
method
network ipv6 interface WIRELESS
configMethod <mode>
<mode> =
automatic
(default) or
static
To verify network settings:
After exiting the above configuration mode and the # prompt
re-appears, type this command to verify all network settings.
show network
QS Rule
Appendix B: Wireless Configuration
USB Wireless LAN Adapters
The EMX supports the following USB Wi-Fi LAN adapters.
Wi-Fi LAN adapters
Supported 802.11
protocols
SparkLAN WUBR-508N
A/B/G/N
Proxim Orinoco 8494
A/B/G
Zyxel NWD271N
B/G
Edimax EW-7722UnD
A/B/G/N
TP-Link TL-WDN3200 v1
A/B/G/N
Raritan USB WIFI
A/B/G/N
Note: To use the Edimax EW-7722UnD or Raritan USB WIFI
wireless LAN adapter to connect to an
802.11n
wireless
network, the handshake timeout setting must be changed to
500 or greater, or the wireless connection will fail.
Supported Wireless LAN Configuration
If wireless networking is preferred, ensure that the wireless
LAN configuration of your EMX matches the access point. The
following is the wireless LAN configuration that the EMX
supports.
Network type: 802.11 A/B/G/N
Protocol: WPA2 (RSN)
Key management: WPA-PSK, or WPA-EAP with PEAP
and MSCHAPv2 authentication
Encryption: CCMP (AES)
Important: Supported 802.11 network protocols vary
according to the wireless LAN adapter being used with the
EMX. See
USB Wireless LAN Adapters
(on page 9).
Making a Wireless Connection
Make the EMX connect to a wireless network as needed.
To make a wireless connection:
Do one of the following:
Plug a supported USB wireless LAN adapter into the
USB-A port on your EMX.
Connect a USB hub to the USB-A port on the EMX.
Then plug the supported USB wireless LAN adapter
into the appropriate USB port on the hub.
See
USB Wireless LAN Adapters
(on page 9) for a list of
supported wireless LAN adapters.
QS Rule
Appendix C: Other Information
Installing the USB-to-Serial Driver (Optional)
The EMX can emulate a USB-to-serial converter over a USB
connection. A USB-to-serial driver named "Dominion EMX
Serial Console" is required for Microsoft
®
Windows
®
operating
systems.
Download the Windows driver for USB serial console from the
Raritan website's
Support page
(
http://www.raritan.com/support/
). The downloaded driver's
name is
dominion-serial-setup-<n>.exe
, where <n>
represents the file's version number.
There are two ways to install this driver: automatic and
manual installation. Automatic driver installation is highly
recommended.
Automatic driver installation in Windows
®
:
1.
Make sure the EMX is NOT connected to the computer via
a USB cable.
2.
Run dominion-serial-setup-<n>.exe on the computer and
follow online instructions to install the driver.
Note: If any Windows security warning appears, accept it
to continue the installation.
3.
Connect the EMX to the computer via a USB cable. The
driver is automatically installed.
Note: Manual installation is required only if the automatic
installation fails. See the section titled "Installing the
USB-to-Serial Driver (Optional)" in the online help for manual
installation procedure.
In Linux:
No additional drivers are required, but you must provide the
name of the tty device, which can be found in the output of the
