Rapidline Boost Plus FXBSTPBTB Instruction Manual Download

Page: 14 / 19

Advanced programming

1Un-Display units setting ------------------------------------------------------------------------------------------------15

2br-Handset brightness setting-----------------------------------------------------------------------------------------15

3bE-Voice setting ---------------------------------------------------------------------------------------------------------------15

4Fu-Go up anti-collision sensitivity setting

----------------------------------------------------------------------------16

5Fd-Go down anti-collision sensitivity setting

-------------------------------------------------------------------------16

6FS-Balance sensitivity

---------------------------------------------------------------------------------------------------------17

7SH-Setting the new lowest display and height range ------------------------------------------------------------17

8Hc-Setting Constant-touch & One-touch --------------------------------------------------------------------------18

9St-Time Reminder setting ---------------------------------------------------------------------------------------------18

10H-Setting bounce height ----------------------------------------------------------------------------------------------18

11r-Restore Factory Defaults

------------------------------------------------------------------------------------------19

12d-Fatigue test mode ---------------------------------------------------------------------------------------------------19

Summary of Contents for Boost Plus FXBSTPBTB




















Search results

Summary of Contents for Boost Plus FXBSTPBTB

Reviews:

Related manuals for Boost Plus FXBSTPBTB

Brands by name

Popular brands

Rapidline Boost Plus FXBSTPBTB, Instruction Manual

Search results

Summary of Contents for Boost Plus FXBSTPBTB

Reviews:

Related manuals for Boost Plus FXBSTPBTB

Brands by name

Popular brands