background image

en-64

7 ADJUSTMENTS

 

 

 

7.10.9 BACKREST ADJUSTMENT (OPTION) __________________________________

The backrest is adjusted using the locking lever (arrow).

The locking lever must latch into the desired position. It should not be 
possible to move the backrest into another position when it is locked.

7.10.10 FORE / AFT ISOLATOR (OPTION) _____________________________________

Under certain driving conditions (for example with a trailer attached), it is useful 
to activate the fore/aft isolator. This means that shock impacts in the driving 
direction can be better absorbed by the driver seat.

Position 1 = fore/aft isolator off
Position 2 = fore/aft isolator on

7.10.11 FORE / AFT ADJUSTMENT (OPTION) __________________________________

The fore/aft adjustment is released by lifting the locking lever.

The locking lever must latch into the desired position. It should not be 
possible to move the driver seat into another position when it is 
locked.

7.10.12 MULTIFUNCTION ARMREST (OPTION) _________________________________

After releasing the hand wheel (arrow), the operator can adjust the armrest ver

-

tical and longitudinal direction; the armrest inclination can be adjusted as well.
The vertical and longitudinal adjustment are effected at the same time in per

-

ceptible steps.

After adjustment has been terminated, tighten the hand-wheel safely

Summary of Contents for MP655





















































































































Reviews: