en-56
7 ADJUSTMENTS
S
1
2
B
A
4314591
K
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
0
A [1]
B [1]
A [1] + B [1]
B [2]
A [1] + B [2]
B [3]
A [1] + B [3]
0
A [1]
B [1]
A [1] + B [1]
B [2]
A [1] + B [2]
B [3]
A [1] + B [3]
X1
Y2
X3
Y4
X5
Y6
X7
Y8
X9
Y10
X11
Y12
X13
Y14
X15
Y16
1 - 2 S H
25 mm
31 mm
38 mm
44 mm
50 mm
57 mm
63 mm
69 mm
76 mm
82 mm
88 mm
95 mm
101 mm
108 mm
114 mm
120 mm
1.0 in
1.25 in
1.50 in
1.75 in
2.0 in
2.25 in
2.50 in
2.75 in
3.0 in
3.25 in
3.50 in
3.75 in
4.0 in
4.25 in
4.50 in
4.75 in
K
X1
Y2
X3
Y4
X5
Y6
X7
Y8
X9
H
H
Y
X
Y16
Y15
Y14
Y13
Y10
Y11
Y12
15
13
11
1
9
7
5
3
16
14
12
10
8
6
4
2
F
G
J
G
H
K
7.2.2
HEIGHT OF CUT ADJUSTMENT (WING cutter decks)_______________________
1.
Raise the deck to mid position.
2.
Remove the quick pin (A) from the top of the caster wheel pivot spindle
3.
Remove the caster wheel from caster support (B).
4.
Select either Position 1 or Position 2 for wheel mounting bracket (C).
To change, remove (4) mounting bolts (D), move to the alternate
location and bolt in place.
5.
Place the selected size and number of spacers (E) below the caster
support. Both A-size (6.5 mm) and B-size (12.5 mm) spacers are
provided. Place the remaining spacers above the caster support.
6.
Replace the quick pin.
7.
Place pin (F) into the proper hole of bracket for the selected height of
cut and fit quick pin (G).
8.
To change level of deck - release nuts (H) locking ball joints in position
and turn the hexagon bar (J) in the center to the right or to the left side
to lift / lower the deck. Fasten when deck is level
S
1
2
B
A
4306795
K
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
0
A [1]
B [1]
A [1] + B [1]
B [2]
A [1] + B [2]
B [3]
A [1] + B [3]
0
A [1]
B [1]
A [1] + B [1]
B [2]
A [1] + B [2]
B [3]
A [1] + B [3]
X1
Y2
X3
Y4
X5
Y6
X7
Y8
X9
Y10
X11
Y12
X13
Y14
X15
Y16
1 - 2 S H
25 mm
31 mm
38 mm
44 mm
50 mm
57 mm
63 mm
69 mm
76 mm
82 mm
88 mm
95 mm
101 mm
108 mm
114 mm
120 mm
1.0 in
1.25 in
1.50 in
1.75 in
2.0 in
2.25 in
2.50 in
2.75 in
3.0 in
3.25 in
3.50 in
3.75 in
4.0 in
4.25 in
4.50 in
4.75 in
K
H
X1
Y2
X3
Y4
X5
Y6
X7
Y8
X9
H
16
14
12
10
8
6
4
2
X
Y
15
13
11
9
7
5
3
1
X15
X13
Y14
Y16
Y10
X11
Y12
A
B
D
C
E
E
Summary of Contents for JMP653
