background image

TF2048903-BA-00 English                                                     

Page 

5

 of 

16

                                                                                    20180615-V1 

 

caution when placing anything in cooking vessel while the appliance is in operation. 

 

Do not move the appliance when in use. Allow the cooking vessel to cool to 115°F 
(45°C) before moving or storing. 

 

For outdoor use only. If stored indoors, detach and leave cylinder outdoors. 

 

This appliance is not intended for and should never be used as a heater. 

 

When cooking with oil or grease, the thermometer provided MUST be used. Follow 
instructions in this manual for proper installation and use of the thermometer. If the 
thermometer supplied with this fryer/boiler has been lost or damaged, a replacement 
thermometer must be one specified by the appliance manufacturer. 

 

This appliance will be HOT during and after use. Use insulated oven mitts or gloves 
for protection from hot surfaces or splatter from cooking liquids. 

 

If the temperature exceeds 400

°

F (200

°

C) or if oil begins to smoke, immediately turn 

the burner or gas supply OFF and wait for the temperature to decrease to less than 
350

°

F (175

°

C) before relighting burner according to this instructions manual. 

 

It is recommended that the cooking vessel not exceed 10.5QT & 12-3/4

” diameter. 

BIGGER VESSEL MAY RESULT IN TIPPING

 

Never overfill the cooking vessel with oil, grease or water than specified by vessel 
manufacturer instruction. If the vessel doesn

’t indicate the maximum fill line, please 

refer to following instructions for determining the maximum fill level. 
Determining the maximum fill level when using a vessel without a maximum line: 
(1) Place the food product in the basket. 
(2) Place the food product and holder into the empty vessel. 
(3) Fill the vessel with water just until the food product is completely submerged. 
There must be a minimum of 3 inch (8 cm) between the water level and top of the 
vessel. 
(4) Remove the food product from the vessel and either mark the water level on the 
side of the vessel or measure the amount of water in the vessel. 
(5) Remove the water and completely dry the vessel and the food product. 
(6) This is the amount of cooking oil the vessel is to be filled with to cook the food 
product. 

 

Introduction of water or ice from any source into the oil/grease may cause overflow 
and severe burns from hot oil and water splatter. When frying with oil/grease, all food 
products MUST be completely 

THAWED

 and towel 

DRIED

 before being immersed in 

the fryer. 

 

Avoid bumping into or impacting the appliance to prevent spillage or splashing of hot 
cooking liquid. 

 

Never drop food or accessories into hot cooking liquid. Lower food and accessories 
slowly into the cooking liquid in order to prevent splashing or overflow. When 
removing food from the appliance care must be taken to avoid burns from hot cooking 
liquids. 

 
 

 

DANGER 

 

 

The safety relief valve on the LP tank could activate the releasing of gas and cause 
an intense fire with risk of death or serious injury. Therefore, follow instructions below 
exactly. 

A.  Do not store a spare LP-gas cylinder under or near this appliance. 
B.  Never fill the cylinder beyond 80 percent full. 
C.  If the instructions in (A) and (B) are not followed exactly, a fire causing death or 

serious injury may occur. 

Summary of Contents for TF2048903-BA

















Reviews: